Nissan Juke Service and Repair Manual : Roof side molding
Exploded View
1. Roof side molding 2. Roof side molding clip 3. Double-sided tape [t: 2.5 mm (0.098 in)] 4. Body side outer panel 5. Roof panel
: Vehicle front
: Do not reuse
Removal and Installation
REMOVAL
ROOF SIDE MODLDING
1. Disengage roof side molding rear side fixing clip, using a remover tool (A).
: Clip
: Vehicle front
CAUTION:
Apply protective tape (B) on body to protect the painted
surface from damage.
2. Pull up roof side molding from rear end to front end.
: Vehicle front
CAUTION:
Never pull the roof side molding strongly.
3. Disengage windshield molding and clip at the front end of roof side molding, and then remove while pulling out toward vehicle rear
: Clip
REMOVAL AND INSTALLATION OF ROOF SIDE MOLDING CLIP REMOVAL
1. Remove roof side molding.
2. Heat adhesive tape interface using a dryer, and then peel roof side molding clips (body side) using longnose pliers.
CAUTION:
Be careful not to damage the body.
INSTALLATION
1. Clean tape removed surface with a shop cloth soaked in white gasoline or IPA.
2. Use two-part epoxy adhesive.
Adhesive : 3M-weld DP–100 or equivalent
3. Apply adhesive evenly to clip tape surface
Thickness : Approximately 0.5 mm (0.020 in)
4. Position applied parts to the proper location, and then sufficiently press-fit until the adhesive protrudes to tape side.
Press-fit limit : 19.6 N× 2 seconds
5. Tape roof side molding clips after press fit, and temporarily hold it for specified time based on the following.
5 to 10°C (41 to 50°F) : 1 hour or more 11 to 23°C (52 to 73°F) : 30 minutes or more 24°C or more (75°F or more) : 15 minutes or more
CAUTION:
• Use double-sided tape after hardening for roof side molding clips.
• Securely insert molding rear end cap onto roof rear end cutout (installation standard).
• When installing roof side molding of windshield glass portion, check that body side molding fastener is securely inserted and then press in.
• Never wash the vehicle within 24 hours so as to keep adhesive.
Fillet molding
Exploded View 1. Grommet 2. Clip 3. Clip 4. Front fillet molding 5. Rear fillet molding : Pawl : Do not reuse Front fillet molding FRONT FILLET MOLDING : Removal and Installation REMOVA ...Door outside molding
Exploded View 1. Front door panel 2. Front door outside molding 3. Rear door panel 4. Rear door outside molding 5. Door glass : Pawl Front door outside molding FRONT DOOR OUTSIDE MOLDING ...Other materials:
Precautions on supplemental restraint system
This Supplemental Restraint System (SRS) section contains important information
concerning the following systems:
• Driver and passenger supplemental frontimpact air bag (NISSAN Advanced Air Bag
System)
• Front seat-mounted side-impact supplemental air bag
• Roof-mounted curtain side-impact s ...
A/C switch
Component Function Check
1.CHECK A/C ON SIGNAL
With CONSULT-III
1. Turn ignition switch ON.
2. Select “AIR CONDITIONER” of “BCM” using CONSULT-III.
3. Select “AIR COND SW” in “DATA MONITOR” mode, and check status under the
following condition.
Is the inspection result normal?
YES >> ...
P0226 APP sensor
DTC Logic
DTC DETECTION LOGIC
Diagnosis Procedure
1.CHECK GROUND CONNECTIONS
1. Turn ignition switch OFF.
2. Check ground connection E38. Refer to Ground inspection in GI-44, "Circuit
Inspection".
Is the inspection result normal?
YES >> GO TO 2.
NO >> Repair or ...