Nissan Juke Service and Repair Manual : Road test

Description

DESCRIPTION

• The purpose of the test is to determine overall performance of CVT and analyze causes of problems.

• The road test consists of the following three parts:

1. “Check Before Engine Is Started” TM-190.

2. “Check at Idle” TM-191.

3. “Cruise Test” TM-192.

• Before road test, familiarize yourself with all test procedures and


• Before road test, familiarize yourself with all test procedures and items to check.

• Perform tests on all items until specified symptom is found. Troubleshoot items the malfunctioning items after road test.

CONSULT-III SETTING PROCEDURE


CONSULT-III SETTING PROCEDURE

• Using CONSULT-III, perform a cruise test and record the result.

• Print the result and ensure that shifts and lock-ups take place as per Shift Schedule.

1. Touch “DATA MONITOR” on “SELECT DIAG MODE” screen.

2. Touch “MAIN SIGNALS” to set recording condition.

3. See “Numerical Display”, “Barchart Display” or “Line Graph Display”.

4. Touch “START”.

5. When performing cruise test. Refer to TM-192, "Cruise Test".

6. After finishing cruise test part, touch “RECORD”.

7. Touch “STORE”.

8. Touch “BACK”.

9. Touch “DISPLAY”.

10. Touch “PRINT”.

11. Check the monitor data printed out.

Check before Engine Is Started

1.CHECK CVT INDICATOR LAMP

1. Park vehicle on flat surface.

2. Move selector lever to “P” position.

3. Turn ignition switch OFF. Wait at least 5 seconds.

4. Turn ignition switch ON. (Do not start engine.)

Is shift position indicator activated for about 2 seconds? YES >> 1. Turn ignition switch OFF.

2. Perform self-diagnosis and note NG items.

Refer to TM-159, "CONSULT-III Function (TRANSMISSION)".

3. Go to TM-191, "Check at Idle".

NO >> Stop “Road Test”. Refer to TM-259, "Symptom Table".

Check at Idle

1.CHECK STARTING THE ENGINE

1. Park vehicle on flat surface.

2. Move selector lever to “P” or “N” position.

3. Turn ignition switch OFF.

4. Turn ignition switch to “START” position.

Is engine started? YES >> GO TO 2.

NO >> Stop “Road Test”. Refer to TM-259, "Symptom Table".

2.CHECK STARTING THE ENGINE

1. Turn ignition switch ON.

2. Move selector lever to “D”, “M” or “R” position.

3. Turn ignition switch to “START” position.

Is engine started? YES >> Stop “Road Test”. Refer to TM-259, "Symptom Table".

NO >> GO TO 3.

3.CHECK “P” POSITION FUNCTION

1. Move selector lever to “P” position.

2. Turn ignition switch OFF.

3. Release parking brake.

4. Push vehicle forward or backward.

5. Apply parking brake.

Does vehicle move forward or backward? YES >> Refer to TM-259, "Symptom Table". Continue “Road Test”.

NO >> GO TO 4.

4.CHECK “N” POSITION FUNCTION

1. Start engine.

2. Move selector lever to “N” position.

3. Release parking brake.

Does vehicle move forward or backward? YES >> Refer to TM-259, "Symptom Table". Continue “Road Test”.

NO >> GO TO 5.

5.CHECK SHIFT SHOCK

1. Apply foot brake.

2. Move selector lever to “R” position.

Is there large shock when changing from “N” to “R” position? YES >> Refer to TM-259, "Symptom Table". Continue “Road Test”.

NO >> GO TO 6.

6.CHECK “R” POSITION FUNCTION

Release foot brake for several seconds.

Does vehicle creep backward when foot brake is released? YES >> GO TO 7.

NO >> Refer toTM-259, "Symptom Table". Continue “Road Test”.

7.CHECK “D” POSITION FUNCTION

Move selector lever to “D” position and check if vehicle creeps forward.

Does vehicle creep forward in all positions? YES >> Go to TM-192, "Cruise Test".

NO >> Stop “Road Test”. Refer to TM-259, "Symptom Table".

Cruise Test

1.CHECK VEHICLE SPEED WHEN SHIFTING GEARS — PART 1

1. Drive vehicle for approximately 10 minutes to warm engine oil and CVT fluid up to operating temperature.

CVT fluid operating temperature: 50 – 80°C (122 – 176°F)

2. Park vehicle on flat surface.

3. Move selector lever to “P” position.

4. Start engine.

5. Move selector lever to “D” position.

6. Accelerate vehicle to 2/8-way throttle depressing accelerator pedal constantly.

speed. Refer to TM-308,Read vehicle speed and engine
speed. Refer to TM-308, "Shift Characteristics".

OK or NG

OK >> GO TO 2.

NG >> Refer to TM-259, "Symptom Table". Continue “Road Test”.

2.CHECK VEHICLE SPEED WHEN SHIFTING GEARS — PART 2


2.CHECK VEHICLE SPEED WHEN SHIFTING GEARS — PART 2

1. Park vehicle on flat surface.

2. Move selector lever to “D” position.

3. Accelerate vehicle to full depression depressing accelerator pedal constantly.

speed.Refer to TM-308,Read vehicle speed and engine
speed.Refer to TM-308, "Shift Characteristics".

OK or NG

OK >> GO TO 3.

NG >> Refer to TM-259, "Symptom Table". Continue “Road Test”.

3.CHECK MANUAL MODE FUNCTION


3.CHECK MANUAL MODE FUNCTION

Move to manual mode from “D” position.

Does it switch to manual mode? YES >> GO TO 4.

NO >> Refer to TM-259, "Symptom Table". Continue “Road Test”.

4.CHECK SHIFT-UP FUNCTION

During manual mode driving, is upshift from M1 → M2 → M3 → M4 → M5 → M6 performed? TM-159, "CONSULT-III Function (TRANSMISSION)".Read the gear position. Refer to
TM-159, "CONSULT-III Function (TRANSMISSION)".

Is upshifting correctly performed? YES >> GO TO 5.

NO >> Refer to TM-259, "Symptom Table". Continue “Road Test”.

5.CHECK SHIFT-DOWN FUNCTION

During manual mode driving, is downshift from M6 → M5 → M4 → M3 → M2 → M1 performed? TM-159, "CONSULT-III Function (TRANSMISSION)".Read the gear position. Refer to
TM-159, "CONSULT-III Function (TRANSMISSION)".

Is downshifting correctly performed? YES >> GO TO 6.

NO >> Refer to TM-259, "Symptom Table". Continue “Road Test”.

6.CHECK ENGINE BRAKE FUNCTION

Check engine brake.

Does engine braking effectively reduce speed in M1 position? YES >> 1. Stop the vehicle.

2. Perform self-diagnosis. Refer to TM-159, "CONSULT-III Function (TRANSMISSION)".

NO >> Refer to TM-259, "Symptom Table". Then continue trouble diagnosis.

    Line pressure test
    Inspection and Judgment INSPECTION Line Pressure Test Port Line Pressure Test Procedure 1. Inspect the amount of engine oil and replenish if necessary. 2. Drive the car for about 10 minutes to ...

    CVT position
    Inspection and Adjustment INSPECTION 1. Place selector lever in “P” position, and turn ignition switch ON (engine stop). 2. Make sure that selector lever can be shifted to other than “P” position ...

    Other materials:

    Diagnosis and repair workflow
    Work Flow INTRODUCTION The TCM receives a signal from the vehicle speed sensor, transmission range switch and provides shift control or lock-up control via CVT solenoid valves. The TCM also communicates with the ECM by means of a signal sent from sensing elements used with the OBD-related p ...

    Vehicle does not enter 4WD mode
    Description Vehicle does not enter 4-wheel drive mode even though 4WD warning lamp turned to OFF. Diagnosis Procedure 1.CHECK 4WD WARNING LAMP Turn the ignition switch ON. Does 4WD warning lamp turn ON? YES >> GO TO 2. NO >> Proceed to diagnosis procedure. Refer to DLN-80, & ...

    Camshaft
    *: Total indicator readin VALVE LIFTER VALVE CLEARANCE *: Approximately 80°C (176°F) AVAILABLE VALVE LIFTER ...