Nissan Juke Owners Manual : Remote keyless entry system (if so equipped)

It is possible to lock/unlock all doors (including the lift gate), and activate the panic alarm by using the keyfob from outside the vehicle.

Before locking the doors, make sure the key is not left in the vehicle.

The keyfob can operate at a distance of approximately 33 ft (10 m) from the vehicle.

(The effective distance depends upon the conditions around the vehicle.) As many as 5 keyfobs can be used with one vehicle. For information concerning the purchase and use of additional keyfobs, contact a NISSAN dealer.

The keyfob will not function in the following situations.

• When the keyfob is not within the operational range.

• When the doors are open or not closed securely.

• When the ignition switch is in the “ON” position.

• When the battery is discharged.

WARNING

The remote keyless entry keyfob transmits radio waves when the buttons are pushed. The FAA advises that the radio waves may affect aircraft navigation and communication systems. Do not operate the keyfob while on an airplane.

Make sure the buttons are not operated unintentionally when the unit is stored during a flight.

CAUTION

The following conditions or occurrences will damage the keyfob.

• Do not allow the keyfob to become wet.

•  Do not drop the keyfob.

• Do not strike the keyfob sharply against another object.

• If the outside temperature is below 148F (−108C), the battery of the Intelligent Key may not function properly.

•  Do not place the keyfob for an extended period in an area where temperatures exceed 1408F (608C).

If a keyfob is lost or stolen, NISSAN recommends erasing the ID code of that keyfob. This will prevent the keyfob from unauthorized use to unlock the vehicle. For information regarding the erasing procedure, please contact a NISSAN dealer.

If the indicator light on the keyfob does not illuminate when pushing the buttons, the keyfob battery may be discharged.

For information regarding the replacement of a battery, see “Key battery replacement” .

1 LOCK button


1 LOCK button 2 UNLOCK button
2 UNLOCK button 3 PANIC button
3 PANIC button 4 Battery indicator light
4 Battery indicator light

HOW TO USE REMOTE KEYLESS ENTRY SYSTEM

Locking doors

1. Remove the key from the ignition switch.

2. Close all the doors.

3. Push the LOCK 4. All the doors will lock. button 1 on the keyfob.


4. All the doors will lock.

All of the doors will lock when the LOCK remains open. button is pushed even though a door
remains open.

5. The hazard indicator flashes twice and the horn chirps once.

• When the LOCK with all doors locked, the hazard indicator flashes twice and the horn chirps once button is pushed
with all doors locked, the hazard indicator flashes twice and the horn chirps once as a reminder that the doors are already locked.

• Operate the door handles to confirm that the doors have been securely locked.

Unlocking doors

1. Push the UNLOCK keyfob. button 2 on the
keyfob.

• The driver’s door unlocks.

• The hazard indicator flashes once if all doors are completely closed.

2. Push the UNLOCK within 5 seconds. button again
within 5 seconds.

• All the doors and the lift gate unlock.

• The hazard indicator flashes once if all doors are completely closed.

All doors will be locked automatically unless one of the following operations is performed within 1 minute of pushing the UNLOCK • Opening any door (including the lift gate). button.


• Opening any door (including the lift gate).

• Placing the ignition switch in the ON position.

Using panic alarm

If you are near your vehicle and feel threatened, you may activate the alarm to call attention as follows: 1. Push the PANIC 1 second. button 3 on the keyfob for more than
1 second.

2. The theft warning alarm and headlights will stay on for 25 seconds.

3. The panic alarm stops when: • It has run for 25 seconds, or •  Any of the buttons on the keyfob is pushed. (Note: the PANIC button must be pushed for more than 1 second.) Battery indicator light

The battery indicator light 4 illuminates when you push any button. If the light does not illuminate, the battery is weak or needs replacement.

For information regarding replacement of a battery, see “Key battery replacement” (P.8- 22).

Setting hazard indicator and horn mode

This vehicle is set in hazard indicator and horn mode when you first receive the vehicle.

In hazard indicator and horn mode, when the LOCK flashes twice and the horn chirps once. button 1 is pushed, the hazard indicator
flashes twice and the horn chirps once.

When the UNLOCK the hazard indicator flashes once. button2 is pushed,
the hazard indicator flashes once.

If the horn chirp is not necessary, you can switch to hazard indicator only mode by following the switching procedure.

In hazard indicator only mode, when the LOCK flashes twice. When the UNLOCK  button button is pushed, the hazard indicator
flashes twice. When the UNLOCK is pushed, neither the hazard indicator nor the horn operates. button
is pushed, neither the hazard indicator nor the horn operates.

Switching procedure:


Switching procedure:

To switch the hazard indicator and horn operation, push the LOCK 2 buttons on the keyfob simultaneously 1 and UNLOCK
for more than 2 seconds. 2 buttons on the keyfob simultaneously
for more than 2 seconds.

• When the hazard indicator mode is set, the hazard indicator flashes 3 times.

• When the hazard indicator and horn mode is set, the hazard indicator flashes once and the horn chirps once.

Intelligent Key system (if so equipped)


    Child safety rear door lock
    Child safety rear door locks help prevent the rear doors from being opened accidentally, especially when small children are in the vehicle. When the levers are in the lock position 1 , the rear d ...

    Intelligent Key system (if so equipped)
    WARNING • Radio waves could adversely affect electric medical equipment. Those who use a pacemaker should contact the electric medical equipment manufacturer for the possible influences before us ...

    Other materials:

    Door cable
    Exploded View LEFT SIDE 1. Heater unit assembly 2. Intake door lever 3. Intake door link 4. Intake door cable 5. Air mix door cable 6. Air mix door link 7. Air mix door rod 8. Lower air mix door lever 9. Upper air mix door lever 10. Max. cool door A. To A/C control RIGHT SIDE ...

    Key ID warning does not operate
    Diagnosis Procedure 1.CHECK DTC WITH BCM AND COMBINATION METER Check that DTC is not detected with BCM and combination meter. Is the inspection result normal? YES >> GO TO 2. NO-1 >> Refer to BCS-67, "DTC Index". (BCM) NO-2 >> Refer to MWI-36, "DTC Index&qu ...

    Idle air volume learning
    Description Idle Air Volume Learning is a function of ECM to learn the idle air volume that keeps each engine idle speed within the specific range. It must be performed under any of the following conditions: • Each time electric throttle control actuator or ECM is replaced. • Idle speed or i ...