Nissan Juke Service and Repair Manual : Rear fog lamp circuit

Component Function Check

1.CHECK REAR FOG LAMP OPERATION

1. Select “RR FOG LAMP” of BCM (HEAD LAMP) active test item.CONSULT-III ACTIVE TEST


1. Select “RR FOG LAMP” of BCM (HEAD LAMP) active test item.

2. With operating the test items, check that the rear fog lamp is turned ON.

On : Rear fog lamp ON Off : Rear fog lamp OFF

Is the inspection result normal? YES >> Rear fog lamp circuit is normal.

NO >> Refer to EXL-56, "Diagnosis Procedure".

Diagnosis Procedure

1.CHECK REAR FOG LAMP BULB

Check applicable lamp bulb.

Is the inspection result normal? YES >> GO TO 2.

NO >> Replace bulb.

2.CHECK REAR FOG LAMP OUTPUT VOLTAGE

1. Turn ignition switch OFF.CONSULT-III ACTIVE TEST


1. Turn ignition switch OFF.

2. Disconnect rear fog lamp connector.

3. Turn ignition switch ON.

4. Select “RR FOG LAMP” of BCM (HEAD LAMP) active test item.

5. With operating the test items, check voltage between rear fog lamp harness connector and ground.

Is the inspection result normal?


Is the inspection result normal? YES >> GO TO 5.

NO >> GO TO 3.

3.CHECK REAR FOG LAMP OPEN CIRCUIT

1. Turn ignition switch OFF.

2. Disconnect BCM connector.

3. Check continuity between BCM harness connector and rear fog lamp harness connector.

*1: Without Intelligent Key


*1: Without Intelligent Key *2: With Intelligent Key

Is the inspection result normal? YES >> GO TO 4.

NO >> Repair or replace harness.

4.CHECK REAR FOG LAMP SHORT CIRCUIT

Check continuity between BCM harness connector and ground.

*1: Without Intelligent Key


*1: Without Intelligent Key *2: With Intelligent Key

Is the inspection result normal? YES >> Check bulb socket for internal short circuit, and if check result is normal, replace BCM. Refer to BCS-93, "Removal and Installation" (with Intelligent Key), BCS-161, "Removal and Installation" (without Intelligent Key).

NO >> Repair or replace harness.

5.CHECK REAR FOG LAMP GROUND OPEN CIRCUIT

Check continuity between rear fog lamp harness connector and ground.

Is the inspection result normal?


Is the inspection result normal? YES >> Check corresponding bulb socket and harness. Repair or replace if necessary.

NO >> Repair or replace harness.

    Front fog lamp circuit
    Component Function Check 1.CHECK FRONT FOG LAMP OPERATION CONSULT-III ACTIVE TEST 1. Select “EXTERNAL LAMPS” of IPDM E/R active test item. 2. With operating the test items, check that the front fo ...

    Parking lamp circuit
    Without daytime running light system WITHOUT DAYTIME RUNNING LIGHT SYSTEM : Component Function Check 1.CHECK PARKING LAMP OPERATION CONSULT-III ACTIVE TEST 1. Select “EXTERNAL LAMPS” of IPDM E/R a ...

    Other materials:

    Drive belt
    Exploded View 1. Alternator 2. Drive belt auto-tensioner 3. Crankshaft pulley 4. A/C compressor 5. Water pump 6. Drive belt A. Possible use range B. Range when new drive belt is installed C. Indicator Checking WARNING: Perform this step when engine is stopped. • Check that th ...

    Precaution Necessary for Steering Wheel Rotation after Battery Disconnect
    NOTE: • Before removing and installing any control units, first turn the ignition switch to the LOCK position, then disconnect both battery cables. • After finishing work, confirm that all control unit connectors are connected properly, then re-connect both battery cables. • Always use CONS ...

    Output speed sensor
    Exploded View 1. Transaxle assembly 2. Output speed sensor 3. O-ring : Vehicle front : Always replace after every disassembly. : N·m (kg-m, in-lb) : Genuine NISSAN CVT Fluid NS-2 Removal and Installation REMOVAL 1. Disconnect battery cable from negative terminal. Refer to PG-124, &qu ...