Nissan Juke Service and Repair Manual : Rear door lock

Exploded View

1. Outside handle assembly


1. Outside handle assembly 2. Rear door sealing screen 3. Door lock assembly
4. TORX bolt
5. Inside handle

: Pawl: Clip
: Vehicle front: Pawl
: Do not reuse: Vehicle front
: N·m (kg-m, in-lb): Do not reuse
: Body grease: N·m (kg-m, in-lb)
Door lock: Body grease


Door lock

DOOR LOCK : Removal and Installation

REMOVAL

1. Remove rear door glass and rear door lower sash (rear). Refer to GW-21, "Removal and Installation".

2. Remove inside handle. Refer to DLK-594, "INSIDE HANDLE : Removal and Installation".

3. Remove outside handle. Refer to DLK-594, "OUTSIDE HANDLE : Removal and Installation".

4. Remove door lock assembly TORX bolts.

5. Disconnect door lock actuator connector, and then remove door lock assembly.

INSTALLATION

Note the following items, and install in the reverse order of removal.

CAUTION:
• Never reuse TORX bolt. Always replace it with a new one when it is removed.

• Check door open/close, lock/unlock operation after installation.

• Check door lock assembly for poor lubrication. Apply body grease to door lock if necessary.

: Grease up point


Inside handle


Inside handle

INSIDE HANDLE : Removal and Installation

REMOVAL

1. Remove rear door finisher. Refer to INT-16, "Removal and Installation".

2. Remove upper side of sealing screen.

NOTE

:
Cut the butyl tape so that some parts of the butyl tape do not remain on the sealing screen, if the sealing screen is reused.

3. Remove inside handle mounting bolt (A).

4. Disengage inside handle (1) from door panel (2) while sliding inside handle toward vehicle rear, and then separate inside handle.

: Vehicle front


5. Disengage inside handle cable (3) and lock knob cable (2), and


5. Disengage inside handle cable (3) and lock knob cable (2), and then remove inside handle (1).

INSTALLATION


INSTALLATION

Note the following item, and install in the reverse order of removal.

CAUTION:
Check door open/close, lock/unlock operation after installation.

Outside handle

OUTSIDE HANDLE : Removal and Installation

REMOVAL

1. Remove rear door finisher and rear door corner cover inner. Refer to INT-16, "Removal and Installation".

2. Remove rear door sealing screen.

3. Rotate stopper (1) upward.

4. Disengage outside handle cable (2), and then remove outside handle cable from outside handle assembly (3).

5. Remove outside handle assembly mounting bolts (A).


5. Remove outside handle assembly mounting bolts (A).

6. Disengage mounting clips using a remover tool (A), and then


6. Disengage mounting clips using a remover tool (A), and then remove outside handle assembly.

CAUTION:
Apply protective tape (B) on the door panel to protect the painted surface from damage.

: Clip


INSTALLATION


INSTALLATION

Note the following items, and install in the reverse order of removal.

CAUTION:
• Never reuse rear door sealing screen. Always replace it with a new one when it is removed. When installing rear door sealing screen, install it according to the following procedure.

- Put lower portion of rear door sealing screen (1) into inside of door panel (2).

- Perform positioning according to the following procedure, and then install rear door sealing screen.

• Align upper portion of rear door sealing screen to hole (A) of door panel as shown in the figure.

• Align hole of rear door sealing screen to edge (B) of door panel as shown in the figure.

• Be careful to position outside handle cable normally when installing it.


• Be careful to position outside handle cable normally when installing it. For details, refer to DLK-593, "Exploded View".

• Check door open/close, lock/unlock operation after installation.

    Front door lock
    Exploded View 1. Door key cylinder assembly (driver side) Outside handle escutcheon (passenger side) 2. Rear gasket 3. Outside handle bracket 4. TORX bolt 5. Key rod (driver side) 6. Doo ...

    Back door lock
    Exploded View 1. Back door lock assembly 2. TORX bolt 3. Back door striker : Do not reuse : N·m (kg-m, ft-lb) : Body grease Door lock DOOR LOCK : Removal and Installation REMOVAL 1. Remo ...

    Other materials:

    Service Notice
    • When removing or installing various parts, place a cloth or padding onto the vehicle body to prevent scratches. • Handle trim, molding, instruments, grille, etc. carefully during removing or installing. Be careful not to oil or damage them. • Apply sealing compound where necessary when ins ...

    B2205 vehicle speed
    Description Vehicle speed signal is transmitted from ABS actuator and electric unit (control unit) via CAN communication to combination meter. DTC Logic DTC DETECTION LOGIC Diagnosis Procedure 1.PERFORM SELF-DIAGNOSIS OF ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) Perform “Self Diagnost ...

    C1609 vehicle speed signal
    DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.PRECONDITIONING If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn ignition switch OFF and wait at least 10 seconds before conducting the next test. >> GO TO 2. 2.DTC REPRODUCTION PROCEDURE With ...