Nissan Juke Service and Repair Manual : Rear door lock

Exploded View

1. Outside handle assembly


1. Outside handle assembly 2. Inside handle
3. TORX bolt
4. Door lock assembly
5. Rear door sealing screen

: Pawl: Clip
: Vehicle front: Pawl
: Do not reuse: Vehicle front
: N·m (kg-m, in-lb): Do not reuse
: Body grease: N·m (kg-m, in-lb)
Door lock: Body grease


Door lock

DOOR LOCK : Removal and Installation

REMOVAL

1. Remove rear door glass and rear door lower sash (rear). Refer to GW-21, "Removal and Installation".

2. Remove inside handle. Refer to DLK-180, "INSIDE HANDLE : Removal and Installation".

3. Remove outside handle. Refer to DLK-180, "OUTSIDE HANDLE : Removal and Installation".

4. Remove door lock assembly TORX bolts.

5. Disconnect door lock actuator connector, and then remove door lock assembly.

INSTALLATION

Note the following items, and install in the reverse order of removal.

CAUTION:
• Never reuse TORX bolt. Always replace it with a new one when it is removed.

• Check door open/close, lock/unlock operation after installation.

• Check door lock assembly for poor lubrication. Apply body grease to door lock if necessary.

: Grease up point


Inside handle


Inside handle

INSIDE HANDLE : Removal and Installation

REMOVAL

1. Remove rear door finisher. Refer to INT-16, "Removal and Installation".

2. Remove upper side of sealing screen.

NOTE

:
Cut the butyl tape so that some parts of the butyl tape do not remain on the sealing screen, if the sealing screen is reused.

3. Remove inside handle mounting bolt (A).

4. Disengage inside handle (1) from door panel (2) while sliding inside handle toward vehicle rear, and then separate inside handle.

: Vehicle front


5. Disengage inside handle cable (2), and then remove inside handle


5. Disengage inside handle cable (2), and then remove inside handle (1).

INSTALLATION


INSTALLATION

Note the following item, and install in the reverse order of removal.

CAUTION:
Check door open/close, lock/unlock operation after installation.

Outside handle

OUTSIDE HANDLE : Removal and Installation

REMOVAL

1. Remove rear door finisher and rear door corner cover inner. Refer to INT-16, "Removal and Installation".

2. Remove rear door sealing screen.

3. Rotate stopper (1) upward.

4. Disengage outside handle cable (2), and then remove outside handle cable from outside handle assembly (3).

5. Remove outside handle assembly mounting bolts (A).


5. Remove outside handle assembly mounting bolts (A).

6. Disengage mounting clips using a remover tool (A), and then


6. Disengage mounting clips using a remover tool (A), and then remove outside handle assembly.

CAUTION:
Apply protective tape (B) on the door panel to protect the painted surface from damage.

: Clip


INSTALLATION: Clip


INSTALLATION

Note the following items, and install in the reverse order of removal.

CAUTION:
• Never reuse rear door sealing screen. Always replace it with a new one when it is removed.

When installing rear door sealing screen, install it according to the following procedure.

- Put lower portion of rear door sealing screen (1) into inside of door panel (2).

- Perform positioning according to the following procedure, and then install rear door sealing screen.

• Align upper portion of rear door sealing screen to hole (A) of door panel as shown in the figure.

• Align hole of rear door sealing screen to edge (B) of door panel as shown in the figure.

• Be careful to position outside handle cable normally when installing it.


• Be careful to position outside handle cable normally when installing it. For details, refer to DLK-179, "Exploded View".

• Check door open/close, lock/unlock operation after installation.

    Front door lock
    Exploded View 1. Door key cylinder assembly (driver side) Outside handle escutcheon (passenger side) 2. Outside handle 3. Front gasket 4. Inside handle 5. TORX bolt 6. Door lock assembly ...

    Back door lock
    Exploded View 1. Back door lock assembly 2. TORX bolt 3. Back door striker : Do not reuse : N·m (kg-m, ft-lb) : Body grease Door lock DOOR LOCK : Removal and Installation REMOVAL 1. Remo ...

    Other materials:

    B1202, B1203, B1204, B1205, B1206, B1207 diagnosis sensor unit
    DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.CHECK SELF-DIAG RESULT With CONSULT-III 1. Turn ignition switch ON. 2. Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT-III. Without CONSULT-III 1. Turn ignition switch ON. 2. Check the air bag warning lamp statu ...

    Side turn signal lamp
    Exploded View 1. Side turn signal lamp bulb 2. Side turn signal lamp hous Removal and Installation CAUTION: Disconnect battery negative terminal or remove the fuse. REMOVAL 1. Remove the side turn signal lamp in numerical order shown in the figure. 2. Rotate the bulb socket counterclockw ...

    System
    WITH AUTO A/C WITH AUTO A/C : System Diagram WITH AUTO A/C : System Description OPERATION DESCRIPTION • BCM detects that the rear window defogger switch turns ON when the ignition switch is ON, and then transmits the rear window defogger switch signal to IPDM E/R via CAN communication for ...