Nissan Juke Service and Repair Manual : Rear disc brake

Brake pad : Inspection and Adj

INSPECTION

Check brake pad wear thickness from an inspection hole on cylinder body. Check using a scale if necessary.

Wear thickness : Refer to BR-137, "Rear Disc Brake".

ADJUSTMENT


ADJUSTMENT

Burnish contact surfaces between disc rotor and brake pads according to the following procedure after refinishing or replacing brake pads, or if a soft pedal occurs at very low mileage.

CAUTION:
• Be careful of vehicle speed because the brake does not operate firmly/securely until pads and disc rotor are securely fitted.

• Only perform this procedure under safe road and traffic conditions. Use extreme caution.

1. Drive vehicle on straight, flat road.

2. Depress brake pedal with the power to stop vehicle within 3 to 5 seconds until the vehicle stops.

3. Drive without depressing brake for a few minutes to cool the brake.

4. Repeat steps 1 to 3 until pad and disc rotor are securely fitted.

Disc rotor : Inspection and Adjustment

INSPECTION

Appearance
Check surface of disc rotor for uneven wear, cracks, and serious damage. Replace it if necessary.

• 2WD: Refer to RAX-5, "Removal and Installation".

• 4WD: Refer to RAX-14, "Removal and Installation".

Runout
1. Fix the disc rotor to the wheel hub and bearing assembly with wheel nuts (2 points at least).

2. Check the wheel bearing axial end play before the inspection.

• 2WD: Refer to RAX-4, "Inspection".

• 4WD: Refer to RAX-12, "Inspection".

3. Inspect the runout with a dial indicator to measure at 10 mm (0.39 in) inside the disc edge.

Runout (with it attached to the vehicle) : Refer to BR-137, "Rear Disc Brake".

4. Find the installation position that has a minimum runout by shifting


4. Find the installation position that has a minimum runout by shifting the disc rotor-to-wheel hub and bearing assembly installation position by one hole at a time if the runout exceeds the limit value.

• Refinish the disc rotor if the runout is outside the limit even after performing the above operation.

CAUTION:
• Check in advance that the thickness of the disc rotor is wear thickness + 0.3 mm (0.012 in) or more.

• If the thickness is less than wear thickness + 0.3 mm (0.012 in), replace the disc rotor.

- 2WD: Refer to RAX-5, "Removal and Installation".

- 4WD: Refer to RAX-14, "Removal and Installation".

Wear thickness : Refer to BR-137, "Rear Disc Brake".

Thickness
Check the thickness of the disc rotor using a micrometer. Replace the disc rotor if the thickness is below the wear limit.

• 2WD: Refer to RAX-5, "Removal and Installation".

• 4WD: Refer to RAX-14, "Removal and Installation".

Wear thickness : Refer to BR-137, "Rear Disc Brake".

ADJUSTMENT


ADJUSTMENT

Burnish contact surfaces between disc rotors and brake pads according to the following procedure after refinishing or replacing disc rotor, or if a soft pedal occurs at very low mileage.

CAUTION:
• Be careful of vehicle speed because the brake does not operate firmly/securely until pad and disc rotor are securely fitted.

• Only perform this procedure under safe road and traffic conditions. Use extreme caution.

1. Drive vehicle on straight, flat road.

2. Depress brake pedal with the power to stop vehicle within 3 to 5 seconds until the vehicle stops.

3. Drive without depressing brake for a few minutes to cool the brake.

4. Repeat steps 1 to 3 until pad and disc rotor are securely fitted.

    Front disc brake
    Brake pad : Inspection and Adjustment INSPECTION Check brake pad wear thickness from an inspection hole on cylinder body. Check using a scale if necessary.Wear thickness : Refer to BR-137, "Fr ...

    Other materials:

    Service Notice or Precautions for Clut
    WARNING: After cleaning clutch disc, wipe it with a dust collector. Never use compressed air. CAUTION: • Clutch fluid use refer to MA-13, "Fluids and Lubricants". • Never reuse drained clutch fluid. • Keep painted surface on the body or other parts free of clutch fluid. If it sp ...

    P0107, P0108 atmospheric pressure sensor
    DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.PRECONDITIONING If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test. 1. Turn ignition switch OFF and wait at least 10 seconds. 2. Turn ignition swi ...

    Diagnosis system (BCM) (without intelligent key system)
    Common item : consult-III Function (BCM - COMMON ITEM) APPLICATION ITEM CONSULT-III performs the following functions via CAN communication with BCM. SYSTEM APPLICATION BCM can perform the following functions for each system. NOTE: It can perform the diagnosis modes except the following for ...