Nissan Juke Service and Repair Manual : Parking, license plate and tail lamps are not turned on

Nissan Juke Service and Repair Manual / Exterior Lighting System Halogen type / Symptom diagnosis / Parking, license plate and tail lamps are not turned on

Without daytime running light system

WITHOUT DAYTIME RUNNING LIGHT SYSTEM : Description

The parking, license plate, tail lamps and each illumination are not turned ON in any condition.

WITHOUT DAYTIME RUNNING LIGHT SYSTEM : Diagnosis Procedure

1.COMBINATION SWITCH INSPECTION

Check the combination switch. Refer to BCS-92, "Symptom Table".

Is the inspection result normal? YES >> GO TO 2.

NO >> Repair or replace the malfunctioning part.

2.CHECK TAIL LAMP RELAY REQUEST SIGNAL INPUT

1. Select “TAIL & CLR REQ” of IPDM E/R data monitor item.CONSULT-III DATA MONITOR


1. Select “TAIL & CLR REQ” of IPDM E/R data monitor item.

2. With operating the lighting switch, check the monitor status.

Is the inspection result normal?


Is the inspection result normal? YES >> Replace IPDM E/R.

NO >> Replace BCM. Refer to BCS-93, "Removal and Installation" (with Intelligent Key), BCS-161, "Removal and Installation" (without Intelligent Key).

With daytime running light system

WITH DAYTIME RUNNING LIGHT SYSTEM : Description

The parking, license plate, tail lamps and each illumination are not turned ON in any condition.

WITH DAYTIME RUNNING LIGHT SYSTEM : Diagnosis Procedure

1.COMBINATION SWITCH INSPECTION

Check combination switch. Refer to BCS-92, "Symptom Table".

Is the combination switch normal? YES >> GO TO 2.

NO >> Repair or replace the malfunctioning part.

2.CHECK TAIL LAMP RELAY REQUEST SIGNAL INPUT

1. Select “TAIL & CLR REQ” of IPDM E/R data monitor item.CONSULT-III DATA MONITOR


1. Select “TAIL & CLR REQ” of IPDM E/R data monitor item.

2. With operating the lighting switch, check the monitor status

Is the inspection result normal?


Is the inspection result normal? YES >> GO TO 3.

NO >> Replace BCM. Refer to BCS-93, "Removal and Installation" (with Intelligent Key), BCS-161, "Removal and Installation" (without Intelligent Key).

3.DAYTIME RUNNING LIGHT RELAY CIRCUIT INSPECTION

Check the daytime running light relay circuit. Refer to EXL-50, "Component Function Check".

Is the inspection result normal? YES >> Replace IPDM E/R.

NO >> Repair or replace the malfunctioning part.

    Both side headlamps (LO) are not turned on
    Description Both side headlamps (LO) are not turned ON in any condition. Diagnosis Procedure 1.CHECK COMBINATION SWITCH Check the combination switch. Refer to BCS-92, "Symptom Table". ...

    Both side front fog lamps are not turned on
    Description The front fog lamps are not turned ON in any condition. Diagnosis Procedure 1.CHECK FUSE Check that the following fuse is fusing. Is the inspection result normal? YES >> GO T ...

    Other materials:

    Vehicle load capacity
    Do not exceed the load limit of your vehicle shown as “The combined weight of occupants and cargo” on the Tire and Loading Information label. Do not exceed the number of occupants shown as “Seating Capacity” on the Tire and Loading Information label. To get “the combined weight of occupants a ...

    Back door trim
    Exploded View 1. Back door side finisher RH 2. Rear parcel shelf finisher 3. Back door side finisher LH 4. Back door lower finisher 5. Emergency lid 6. Back door pull handle : Clip : Pawl Back door pull handle : Removal and Installation REMOVAL CAUTION: • When removing, always use ...

    LAN System can system (type 2)
    DTC/circuit diagnosis Main line between IPDM-E AND DLC circuit Diagnosis Procedure 1.CHECK CONNECTOR 1. Turn the ignition switch OFF. 2. Disconnect the battery cable from the negative terminal. 3. Check the following terminals and connectors for damage, bend and loose connection (connector s ...