Nissan Juke Service and Repair Manual : Parking lamp circuit
Without daytime running light system
WITHOUT DAYTIME RUNNING LIGHT SYSTEM : Component Function Check
1.CHECK PARKING LAMP OPERATION
CONSULT-III ACTIVE TEST
1. Select “EXTERNAL LAMPS” of IPDM E/R active test item.
2. With operating the test items, check that the parking lamp is turned ON.
TAIL : Parking lamp ON Off : Parking lamp OFF
Is the inspection result normal? YES >> Parking lamp circuit is normal.
NO >> Refer to EXL-60, "WITH DAYTIME RUNNING LIGHT SYSTEM : Diagnosis Procedure".
WITHOUT DAYTIME RUNNING LIGHT SYSTEM : Diagnosis Procedure
1.CHECK PARKING LAMP FUSE
1. Turn ignition switch OFF.
2. Check that the following fuses are not fusing.
Is the inspection result normal? YES >> GO TO 3.
NO >> GO TO 2.
2.CHECK PARKING LAMP SHORT CIRCUIT
1. Disconnect the following connectors.
- IPDM E/R
- Parking lamp
- Rear combination lamp (RH)
- License plate lamp
2. Check continuity between IPDM E/R harness connector and ground.
Is the inspection result normal? YES >> Replace fuse. (Replace IPDM E/R if fusing is found again.) NO >> Repair or replace harness. And then replace the fuse.
3.CHECK PARKING LAMP BULB
Check applicable lamp bulb.
Is the inspection result normal? YES >> GO TO 4.
NO >> Replace bulb.
4.CHECK PARKING LAMP OUTPUT VOLTAGE
CONSULT-III ACTIVE TEST
1. Disconnect parking lamp connector.
2. Turn ignition switch ON.
3. Select “EXTERNAL LAMPS” of IPDM E/R active test item.
4. With operating the test items, check voltage between IPDM E/R harness connector and ground.
Is the inspection result normal? YES >> GO TO 5.
NO >> Replace IPDM E/R.
5.CHECK PARKING LAMP OPEN CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect IPDM E/R connector.
3. Check continuity between IPDM E/R harness connector and parking lamp harness connector.
Is the inspection result normal? YES >> GO TO 6.
NO >> Repair or replace harness.
6.CHECK PARKING LAMP GROUND OPEN CIRCUIT
Check continuity between parking lamp harness connector and ground.
Is the inspection result normal? YES >> Check corresponding bulb socket and harness. Repair or replace if necessary.
NO >> Repair or replace harness.
With daytime running light system
WITH DAYTIME RUNNING LIGHT SYSTEM : Component Function Check
1.CHECK PARKING LAMP OPERATION
CONSULT-III ACTIVE TEST
1. Select “EXTERNAL LAMPS” of IPDM E/R active test item.
2. With operating the test items, check that the parking lamp is turned ON.
TAIL : Parking lamp ON Off : Parking lamp OFF
Is the inspection result normal? YES >> Parking lamp circuit is normal.
NO >> Refer to EXL-60, "WITH DAYTIME RUNNING LIGHT SYSTEM : Diagnosis Procedure".
WITH DAYTIME RUNNING LIGHT SYSTEM : Diagnosis Procedure
1.CHECK PARKING LAMP BULB
Check applicable lamp bulb.
Is the inspection result normal? YES >> GO TO 2.
NO >> Replace bulb.
2.CHECK PARKING LAMP OPEN CIRCUIT
1. Turn ignition switch OFF.
2. Remove daytime running light relay.
3. Disconnect parking lamp connector.
4. Check continuity between daytime running light relay harness connector and parking lamp harness connector.
Is the inspection result normal? YES >> GO TO 3.
NO >> Repair or replace harness.
3.CHECK PARKING LAMP SHORT CIRCUIT
1. Disconnect the following connectors.
- Rear combination lamp (RH) - License plate lamp
2. Check continuity between daytime running light relay harness connector and ground.
Is the inspection result normal? YES >> GO TO 4.
NO >> Repair or replace harness.
4.CHECK PARKING LAMP GROUND OPEN CIRCUIT
Check continuity between parking lamp harness connector and ground.
Is the inspection result normal? YES >> Check corresponding bulb socket and harness. Repair or replace if necessary.
NO >> Repair or replace harness.
Rear fog lamp circuit
Component Function Check 1.CHECK REAR FOG LAMP OPERATION CONSULT-III ACTIVE TEST 1. Select “RR FOG LAMP” of BCM (HEAD LAMP) active test item. 2. With operating the test items, check that the rear ...Tail lamp circuit
Without daytime running light system WITHOUT DAYTIME RUNNING LIGHT SYSTEM : Component Function 1.CHECK TAIL LAMP OPERATION CONSULT-III ACTIVE TEST 1. Select “EXTERNAL LAMPS” of IPDM E/R active tes ...Other materials:
Diagnosis Procedure
WARNING:
• Before servicing, turn ignition switch OFF, disconnect battery negative
terminal and wait at least 3
minutes. (To discharge backup capacitor.)
• Never use unspecified tester or other measuring device.
1.CHECK HARNESS CONNECTOR
Check the harness connector.
Is the inspection res ...
C1130 engine signal
DTC Logic
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.PRECONDITIONING
If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn
ignition switch OFF and
wait at least 10 seconds before conducting the next test.
>> GO TO 2.
2.CHECK DTC DETECTION
With CONSULT ...
Door lock operation warning does not operate
Diagnosis Procedure
1.CHECK DOOR LOCK FUNCTION
Check door lock function.
Does door lock/unlock using door request switch?
YES >> GO TO 2.
NO >> Refer to DLK-85, "Component Function Check".
2.CHECK INTELLIGENT KEY WARNING BUZZER
Check Intelligent Key warning buzzer. ...