Nissan Juke Service and Repair Manual : P range interlock door lock/unlock function does not operate
Diagnosis Procedure
1.CHECK “AUTOMATIC LOCK/UNLOCK SELECT” SETTING IN “WORK SUPPORT”
1. Select “DOOR LOCK” of “BCM” using CONSULT-III.
2. Select “AUTOMATIC LOCK/UNLOCK SELECT” in “WORK SUPPORT” mode.
3. Check “AUTOMATIC LOCK/UNLOCK SELECT” setting in “WORK SUPPORT”.
Refer to DLK-371, "DOOR LOCK : CONSULT-III Function (BCM - DOOR LOCK) (With Super Lock)".
Is the inspection result normal? YES >> GO TO 2.
NO >> Set “Unlock Only”, “Lock Only” or “Lock/Unlock” in “AUTOMATIC LOCK/UNLOCK SELECT”.
2.CHECK “AUTOMATIC DOOR LOCK SELECT” SETTING IN “WORK SUPPORT”
1. Select “DOOR LOCK” of “BCM” using CONSULT-III.
2. Select “AUTOMATIC DOOR LOCK SELECT” in “WORK SUPPORT” mode.
3. Check “AUTOMATIC DOOR LOCK SELECT” setting in “WORK SUPPORT”.
Refer to DLK-371, "DOOR LOCK : CONSULT-III Function (BCM - DOOR LOCK) (With Super Lock)".
Is the inspection result normal? YES >> GO TO 3.
NO >> Set “P RANGE” in “AUTOMATIC DOOR LOCK SELECT”.
3.CHECK “AUTOMATIC DOOR UNLOCK SELECT” SETTING IN “WORK SUPPORT”
1. Select “DOOR LOCK” of “BCM” using CONSULT-III.
2. Select “AUTOMATIC DOOR UNLOCK SELECT” in “WORK SUPPORT” mode.
3. Check “AUTOMATIC DOOR UNLOCK SELECT” setting in “WORK SUPPORT”.
Refer to DLK-371, "DOOR LOCK : CONSULT-III Function (BCM - DOOR LOCK) (With Super Lock)".
Is the inspection result normal? YES >> GO TO 4.
NO >> Set “MODE 2” or “MODE 4” in “AUTOMATIC DOOR UNLOCK SELECT”.
4.CHECK TCM
Check TCM for DTC.
Refer to TM-171, "DTC Index" (RE0F10B models) or TM-366, "DTC Index" (RE0F11A models).
Is the inspection result normal? YES >> GO TO 5.
NO >> Repair or replace the malfunctioning parts.
5.REPLACE BCM
• Replace BCM. Refer to BCS-161, "Removal and Installation".
• Confirm the operation after replacement.
Is the result normal? YES >> INSPECTION END
NO >> Check intermittent incident. Refer to GI-42, "Intermittent Incident".
IGN off interlock door unlock function does not operate
Diagnosis Procedure 1.CHECK “AUTOMATIC LOCK/UNLOCK SELECT” SETTING IN “WORK SUPPORT” 1. Select “DOOR LOCK” of “BCM” using CONSULT-III. 2. Select “AUTOMATIC LOCK/UNLOCK SELECT” in “WORK SUPPORT” mod ...Auto door lock operation does not operate
Diagnosis Procedure 1.CHECK “AUTO LOCK SET” SETTING WITH CONSULT-III 1. Select “MULTI REMOTE ENT” of “BCM” using CONSULT-III. 2. Select “AUTO LOCK SET” in “WORK SUPPORT” mode. 3. Check “AUTO LOCK ...Other materials:
Precaution Necessary for Steering Wheel Rotation after Battery Disconnect
NOTE:
• Before removing and installing any control units, first turn the ignition
switch to the LOCK position, then disconnect
both battery cables.
• After finishing work, confirm that all control unit connectors are connected
properly, then re-connect both
battery cables.
• Always use CONS ...
Diagnosis system (TCM)
CONSULT-III Function (TRANSMISSION)
CONSULT-III can display each diagnostic item using the diagnostic test modes
shown below.
FUNCTION
*: “Function Test” can be selected, but do not use it.
WORK SUPPORT MODE
Display Item List
Engine Brake Adjustment
“ENGINE BRAKE LEVEL”
0: Initial ...
B2193 chain of ECM-IMMU
DTC Logic
DTC DETECTION LOGIC
NOTE:
• If DTC B2193 is displayed with DTC U1000, first perform the trouble diagnosis
for DTC U1000. Refer to
BCS-153, "DTC Logic".
• If DTC B2193 is displayed with DTC U1010, first perform the trouble diagnosis
for DTC U1010. Refer to
BCS-154, " ...