Nissan Juke Service and Repair Manual : P245A EGR cooler bypass valve control solenoid valve
DTC Logic
DTC DETECTION LOGIC
NOTE
:
If DTC P245A is displayed with DTC P0560 or P0657, first perform trouble
diagnosis for DTC P0560 or P0657.
Refer to EC-963, "DTC Logic" (DTC P0560) or EC-976, "DTC Logic" (DTC P0657).
Diagnosis Procedure
1.CHECK GROUND CONNECTIONS
1. Turn ignition switch OFF.
2. Check ground connection E38. Refer to Ground inspection in GI-44, "Circuit Inspection".
Is the inspection result normal? YES >> GO TO 2.
NO >> Repair or replace ground connection.
2.CHECK EGR COOLER BYPASS VALVE CONTROL SOLENOID VALVE POWER SUPPLY CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect EGR cooler bypass valve control solenoid valve harness connector.
3. Turn ignition switch ON.
4. Check the voltage between EGR cooler bypass valve control solenoid valve harness connector and ground.
Is the inspection result normal? YES >> GO TO 4.
NO >> GO TO 3.
3.DETECT MALFUNCTIONING PART
Check the following.
• Harness connectors E8, F1 • Harness for open or short between IPDM E/R and EGR cooler bypass valve control solenoid valve
>> Repair open circuit or short to ground or short to power in harness or connectors.
4.CHECK EGR COOLER BYPASS VALVE CONTROL SOLENOID VALVE GROUND CIRCUIT FOR OPEN AND SHORT
1. Turn ignition switch OFF.
2. Disconnect ECM harness connectors.
3. Check the continuity between EGR cooler bypass valve control solenoid valve harness connector and ECM harness connector.
4. Also check harness for short to ground and short to power.
Is the inspection result normal? YES >> GO TO 5.
NO >> Repair open circuit or short to ground or short to power in harness or connectors.
5.CHECK EGR COOLER BYPASS VALVE CONTROL SOLENOID VALVE
Refer to EC-1007, "Component Inspection".
Is the inspection result normal? YES >> GO TO 6.
NO >> Replace EGR cooler bypass valve control solenoid valve.
6.CHECK INTERMITTENT INCIDENT
Refer to GI-42, "Intermittent Incident".
>> INSPECTION END
Component Inspection
1.CHECK EGR COOLER BYPASS VALVE CONTROL SOLENOID VALVE
1. Reconnect all harness connectors disconnected.
2. Measure the voltage signal between ECM harness connector and ground under the following conditions.
Is the inspection result normal? YES >> INSPECTION END
NO >> Replace EGR cooler bypass valve control solenoid valve.
P2263 TC system
DTC Logic DTC DETECTION LOGIC Diagnosis Procedure 1.CHECK VACUUM HOSES AND VACUUM GALLERY 1. Turn ignition switch OFF. 2. Check vacuum hoses and vacuum gallery for clogging, cracks or improper ...PC415 communication circuit
Description CAN (Controller Area Network) is a serial communication line for real time application. It is an on-vehicle multiplex communication line with high data communication speed and excellen ...Other materials:
Symptom diagnosis
Squeak and rattle trouble diagnoses
Work Flow
CUSTOMER INTERVIEW
Interview the customer if possible, to determine the conditions that exist
when the noise occurs. Use the Diagnostic
Worksheet during the interview to document the facts and conditions when the
noise occurs and any of
the cu ...
Exploded View
1. Main muffler
2. Mounting rubber
3. Ring gasket
4. Center tube
5. Exhaust gas temperature sensor 2
6. Diesel particulate filter assembly
7. Gasket
8. Stud bolt
9. Diesel particulate filter inlet tube
10. Gasket
A. To exhaust manifold
B. To pressure hose
: N·m (kg-m, ft-lb)
: ...
Diagnosis system (BCM)
Common item : consult-III Function (BCM - COMMON ITEM)
APPLICATION ITEM
CONSULT-III performs the following functions via CAN communication with BCM.
SYSTEM APPLICATION
BCM can perform the following functions for each system.
NOTE:
It can perform the diagnosis modes except the following for ...