Nissan Juke Service and Repair Manual : P2138 APP sensor

DTC Logic

DTC DETECTION LOGIC

NOTE

:
If DTC P2138 is displayed with DTC P0643, first perform the trouble diagnosis for DTC P0643. Refer to EC-307, "DTC Logic".

DTC CONFIRMATION PROCEDURE


DTC CONFIRMATION PROCEDURE

1.PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.

1. Turn ignition switch OFF and wait at least 10 seconds.

2. Turn ignition switch ON.

3. Turn ignition switch OFF and wait at least 10 seconds.

TESTING CONDITION:
Before performing the following procedure, confirm that battery voltage is more than 8 V at idle.

>> GO TO 2.

2.PERFORM DTC CONFIRMATION PROCEDURE

1. Start engine and let it idle for 1 second.

2. Check DTC.

Is DTC detected? YES >> Proceed to EC-395, "Diagnosis Procedure".

NO >> INSPECTION END

Diagnosis Procedure

1.CHECK APP SENSOR 1 POWER SUPPLY

1. Turn ignition switch OFF.

2. Disconnect accelerator pedal position (APP) sensor harness connector.

3. Turn ignition switch ON.

4. Check the voltage between APP sensor harness connector and ground.

*1: LHD models or RHD with CVT models


*1: LHD models or RHD with CVT models *2: RHD with M/T models

Is the inspection result normal? YES >> GO TO 3.

NO >> GO TO 2.

2.CHECK APP SENSOR 1 POWER SUPPLY CIRCUIT

1. Turn ignition switch OFF.

2. Disconnect ECM harness connector.

3. Check the continuity between APP sensor harness connector and ECM harness connector.

*1: LHD models or RHD with CVT models


*1: LHD models or RHD with CVT models *2: RHD with M/T models

4. Also check harness for short to ground.

Is the inspection result normal? YES >> Perform the trouble diagnosis for power supply circuit.

NO >> Repair or replace error-detected parts.

3.CHECK APP SENSOR 2 POWER SUPPLY

Check the voltage between APP sensor harness connector and ground.

*1: LHD models or RHD with CVT models


*1: LHD models or RHD with CVT models *2: RHD with M/T models

Is the inspection result normal? YES >> GO TO 5.

NO >> GO TO 4.

4.CHECK SENSOR POWER SUPPLY CIRCUIT

1. Turn ignition switch OFF.

2. Disconnect ECM harness connector.

3. Check harness connector for short to power and short to ground, between the following terminals.

*1: LHD models or RHD with CVT models


*1: LHD models or RHD with CVT models *2: RHD with M/T models

Is inspection result normal? YES >> Perform the trouble diagnosis for power supply circuit.

NO >> Repair or replace error-detected parts.

5.CHECK APP SENSOR GROUND CIRCUIT

1. Turn ignition switch OFF.

2. Disconnect ECM harness connector.

3. Check the continuity between APP sensor harness connector and ECM harness connector.

*1: LHD models or RHD with CVT models


*1: LHD models or RHD with CVT models *2: RHD with M/T models

4. Also check harness for short to power.

Is the inspection result normal? YES >> GO TO 6.

NO >> Repair or replace error-detected parts.

6.CHECK APP SENSOR INPUT SIGNAL CIRCUIT

1. Check the continuity between APP sensor harness connector and ECM harness connector.

*1: LHD models or RHD with CVT models


*1: LHD models or RHD with CVT models *2: RHD with M/T models

2. Also check harness for short to ground and to power.

Is the inspection result normal?

YES >> GO TO 7.

NO >> Repair or replace error-detected parts 7.CHECK APP SENSOR

Check the APP sensor. Refer to EC-390, "Component Inspection".

Is the inspection result normal? YES >> Check intermittent incident. Refer to GI-42, "Intermittent Incident".

NO >> Replace accelerator pedal assembly. Refer to EM-28, "Exploded View".

Component Inspection

1.CHECK ACCELERATOR PEDAL POSITION SENSOR

1. Turn ignition switch OFF.

2. Reconnect all harness connectors disconnected.

3. Turn ignition switch ON.

4. Check the voltage between ECM harness connector terminals as per the following condition.

Is the inspection result normal?


Is the inspection result normal? YES >> INSPECTION END

NO >> Replace accelerator pedal assembly. Refer to EM-28, "Exploded View".

    P2135 TP sensor
    DTC Logic DTC DETECTION LOGIC NOTE: If DTC P2135 is displayed with DTC P0643, first perform the trouble diagnosis for DTC P0643. Refer to EC-307, "DTC Logic". DTC CONFIRMATION PROCE ...

    P2162 vehicle speed sensor
    Description ECM receives a rear wheel sensor signal from ABS actuator and electric unit (control unit) via CAN communication to switch combustion for the direct injection gasoline system. For the ...

    Other materials:

    For side and rollover collision : When SRS is not activated in a collision
    CAUTION: Due to varying models and option levels, not all parts listed in the chart below apply to all vehicles. WORK PROCEDURE 1. Before performing any of the following steps, ensure that all vehicle body and structural repairs have been completed. 2. Check the SRS components and the rel ...

    Windshield wiper and washer switch
    WARNING In freezing temperatures the washer solution may freeze on the windshield and obscure your vision which may lead to an accident. Warm windshield with the defroster before you wash the windshield. CAUTION • Do not operate the washer continuously for more than 30 seconds. • Do not oper ...

    System
    Relay control system RELAY CONTROL SYSTEM : System Diagram *1: Except for MR16DDT engine models *2: For MR16DDT engine models RELAY CONTROL SYSTEM : System Description IPDM E/R activates the internal control circuit to perform the relay ON-OFF control according to the input signals from va ...