Nissan Juke Service and Repair Manual : P2120 APP sensor

DTC Logic

DTC DETECTION LOGIC

Diagnosis Procedure


Diagnosis Procedure

1.CHECK GROUND CONNECTIONS

1. Turn ignition switch OFF.

2. Check ground connection E38. Refer to Ground inspection in GI-44, "Circuit Inspection".

Is the inspection result normal? YES >> GO TO 2.

NO >> Repair or replace ground connection.

2.CHECK ACCELERATOR PEDAL POSITION SENSOR POWER SUPPLY CIRCUIT

1. Disconnect accelerator pedal position sensor harness connector.

2. Turn ignition switch ON.

3. Check the voltage between accelerator pedal position sensor connector and ground.

Is the inspection result normal?


Is the inspection result normal? YES >> GO TO 4.

NO >> GO TO 3.

3.DETECT MALFUNCTIONING PART

• Harness connectors E105, M77 (RHD models) • Harness connectors M95, M202 (RHD models) • Harness for open or short between ECM and accelerator pedal position sensor

>> Repair open circuit or short to ground or short to power in harness or connector.

4.CHECK ACCELERATOR PEDAL POSITION SENSOR GROUND CIRCUIT FOR OPEN AND SHORT

1. Turn ignition switch OFF.

2. Disconnect accelerator pedal position sensor.

3. Check the continuity between accelerator pedal position sensor harness connector and ECM harness connector.

4. Also check harness for short to ground and short to power.


4. Also check harness for short to ground and short to power.

Is the inspection result normal? YES >> GO TO 6.

NO >> GO TO 5.

5.DETECT MALFUNCTIONING PART

• Harness connectors E105, M77 (RHD models) • Harness connectors M95, M202 (RHD models) • Harness for open or short between ECM and accelerator pedal position sensor

>> Repair open circuit or short to ground or short to power in harness or connector.

6.CHECK ACCELERATOR PEDAL POSITION SENSOR INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT

1. Check the continuity between accelerator pedal position sensor harness connector and ECM harness

2. Also check harness for short to ground and short to power.


2. Also check harness for short to ground and short to power.

Is the inspection result normal? YES >> GO TO 8.

NO >> GO TO 7.

7.DETECT MALFUNCTIONING PART

• Harness connectors E105, M77 (RHD models) • Harness connectors M95, M202 (RHD models) • Harness for open or short between ECM and accelerator pedal position sensor

>> Repair open circuit or short to ground or short to power in harness or connector.

8.CHECK ACCELERATOR PEDAL POSITION SENSOR

Refer to EC-1001, "Component Inspection".

Is the inspection result normal? YES >> GO TO 9.

NO >> Replace accelerator pedal position sensor.

9.CHECK INTERMITTENT INCIDENT

Refer to GI-42, "Intermittent Incident", ???INCIDENT SIMULATION TESTS??? and ???GROUND INSPECTION???.

>> INSPECTION END

Component Inspection

1.CHECK ACCELERATOR PEDAL POSITION SENSOR

1. Turn ignition switch OFF.

2. Disconnect accelerator pedal position sensor harness connector.

3. Check resistance between accelerator pedal position sensor as follows.

Is the inspection result normal?


Is the inspection result normal? YES >> INSPECTION END

NO >> Replace accelerator pedal position sensor.

    P2119 electric throttle control function
    DTC Logic DTC DETECTION LOGIC Diagnosis Procedure 1.CHECK INTERMITTENT INCIDENT Refer to GI-42, "Intermittent Incident". Is the inspection result normal? YES >> GO TO 2. N ...

    P2226 baro sensor
    DTC Logic DTC DETECTION LOGIC Diagnosis Procedure 1.REPLACE ECM Perform EC-879, "Work Procedure". >> INSPECTION END ...

    Other materials:

    Break-in schedule
    CAUTION During the first 1,200 miles (2,000 km), follow these recommendations to obtain maximum engine performance and ensure the future reliability and economy of your new vehicle. Failure to follow these recommendations may result in shortened engine life and reduced engine performance. •& ...

    Precaution Necessary for Steering Wheel Rotation after Battery Disconnect
    NOTE: • Before removing and installing any control units, first turn the ignition switch to the LOCK position, then disconnect both battery cables. • After finishing work, confirm that all control unit connectors are connected properly, then re-connect both battery cables. • Always use CONS ...

    Starting difficult with cold engine
    Description CHART 3: STARTING DIFFICULT WITH COLD ENGINE Diagnosis Procedure 1.CHECK ENGINE OIL LEVEL Is the engine oil level correct? Yes or No Yes >> GO TO 2. No >> Top up the oil. 2.CHECK ENGINE OIL Check the grade of engine oil. Refer to LU-33, "Inspection". ...