Nissan Juke Service and Repair Manual : P183B solenoid power supply

DTC Logic

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE


DTC CONFIRMATION PROCEDURE

1.PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn ignition switch OFF and wait at least 10 seconds before conducting the next test.

>> GO TO 2.

2.DTC REPRODUCTION PROCEDURE

1. Turn the ignition switch OFF to ON.With CONSULT-III


1. Turn the ignition switch OFF to ON.

2. Perform self-diagnosis for “ALL MODE AWD/4WD”.

Is DTC “P183B” detected? YES >> Proceed to diagnosis procedure. Refer to DLN-67, "Diagnosis Procedure".

NO >> INSPECTION END

Diagnosis Procedure

1.CHECK 4WD SOLENOID POWER SUPPLY (1)

1. Turn the ignition switch OFF.

2. Disconnect 4WD control module harness connector.

3. Check the voltage between 4WD control module harness connector and ground.

4. Turn the ignition switch OFF to ON.


4. Turn the ignition switch OFF to ON.

CAUTION:
Never start the engine.

5. Check the voltage between 4WD control module harness connector and ground.

Is the inspection result normal?


Is the inspection result normal? YES >> GO TO 3.

NO >> GO TO 2.

2.CHECK 4WD SOLENOID POWER SUPPLY (2)

1. Turn the ignition switch OFF.

2. Check the 10A fuse (#12).

3. Check the harness for open or short between 4WD control module harness connector No.12 and the 10A fuse (#12).

Is the inspection result normal?

YES >> Perform the trouble the diagnosis for power supply circuit. Refer to PG-10, "Wiring Diagram - BATTERY POWER SUPPLY -".

NO >> Repair or replace error-detected parts.

3.CHECK 4WD CONTROL MODULE POWER SUPPLY (1)

1. Turn the ignition switch OFF.

2. Check the voltage between 4WD control module harness connector and ground.

3. Turn the ignition switch ON.


3. Turn the ignition switch ON.

CAUTION:
Never start the engine.

4. Check the voltage between 4WD control module harness connector and ground.

Is the inspection result normal?


Is the inspection result normal? YES >> GO TO 5.

NO >> GO TO 4.

4.CHECK 4WD CONTROL MODULE POWER SUPPLY (2)

1. Turn the ignition switch OFF.

2. Check the 10A fuse (#3).

3. Check the harness for open or short between 4WD control module harness connector No.3 terminal and 10A (#3).

Is the inspection result normal? YES >> Perform the trouble diagnosis for ignition power supply circuit. Refer to PG-15, "Wiring Diagram - IGNITION POWER SUPPLY -".

NO >> Repair or replace error-detected parts.

5.CHECK 4WD SOLENOID GROUND

Check the continuity between 4WD control module harness connector and ground.

Is the inspection result normal?


Is the inspection result normal? YES >> GO TO 6.

NO >> Repair or replace the error-detected parts.

6.CHECK TERMINALS AND HARNESS CONNECTORS

1. Check 4WD control module pin terminals for damage or loose connection with harness connector.

2. Check 4WD solenoid pin terminals for damage or loose connection with harness connector.

Is the inspection result normal? YES >> Replace 4WD control module. Refer to DLN-91, "Removal and Installation".

NO >> Repair or replace the error-detected parts.

    P183A coupling temperature sensor right
    DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.PRECONDITIONING If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn ignition switch OFF and wait at least 10 ...

    P183C decel G sensor
    DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.PRECONDITIONING If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn ignition switch OFF and wait at least 10 ...

    Other materials:

    Passenger compartment
    CAUTION Never use a fuse of a higher or lower amperage rating than that specified on the fuse box cover. This could damage the electrical system or cause a fire. If any electrical equipment does not operate, check for an open fuse. 1. Be sure the ignition switch and the headlight switch are t ...

    Integrated control system (if so equipped)
    The Integrated Control System is located below the audio system or navigation system (if so equipped). Two Integrated Control System modes can be selected: Drive mode and Climate Control mode. Depending on which Integrated Control System mode is selected (Drive mode or Climate Control mode), ...

    U1402 engine speed signal
    DTC Logic DTC DETECTION LOGIC Diagnosis Procedure 1.PERFORM ECM SELF DIAGNOSIS Using CONSULT-III, check the “self diagnosis result” of “ENGINE” and repair or replace any malfunctioning parts. >> • Refer to EC-108, "DTC Index". (MR16DDT) • Refer to EC-522, "DTC Index ...