Nissan Juke Service and Repair Manual : P183A coupling temperature sensor right

DTC Logic

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE


DTC CONFIRMATION PROCEDURE

1.PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn ignition switch OFF and wait at least 10 seconds before conducting the next test.

>> GO TO 2.

2.DTC REPRODUCTION PROCEDURE

1. Turn the ignition switch OFF to ON.With CONSULT-III


1. Turn the ignition switch OFF to ON.

2. Perform self-diagnosis for “ALL MODE AWD/4WD”.

Is DTC “P183A” detected? YES >> Proceed to diagnosis procedure. Refer to DLN-65, "Diagnosis Procedure".

NO >> INSPECTION END

Diagnosis Procedure

1.CHECK ELECTRIC CONTROLLED COUPLING (RH) TEMPERATURE SENSOR POWER SUPPLY

1. Turn the ignition switch OFF.

2. Disconnect transfer fluid temperature sensor harness connector.

3. Turn the ignition switch ON.

CAUTION:
Never start the engine.

4. Check the voltage between rear final drive assembly harness connector terminals.

Is the inspection result normal?


Is the inspection result normal? YES >> GO TO 3.

NO >> GO TO 2.

2.CHECK ELECTRIC CONTROLLED COUPLING (RH) TEMPERATURE SENSOR CIRCUIT

1. Turn the ignition switch OFF.

2. Disconnect 4WD control module harness connector.

3. Check the continuit

4. Check the continuity between transfer fluid temperature sensor harness


4. Check the continuity between transfer fluid temperature sensor harness connector and ground.

Is the inspection result normal?


Is the inspection result normal? YES >> GO TO 4.

NO >> Repair or replace error-detected parts.

3.CHECK ELECTRIC CONTROLLED COUPLING (RH) TEMPERATURE SENSOR

Check the electric controlled coupling (RH) temperature sensor. Refer to DLN-66, "Component Inspection".

Is the inspection result normal? YES >> GO TO 4.

NO >> Electric controlled coupling (RH) temperature sensor is malfunctioning. Replace electric controlled coupling (RH). Refer to DLN-139, "Removal and Installation".

4.CHECK TERMINALS AND HARNESS CONNECTORS

Check the pin terminals for damage or loose connection with each harness connector.

Is the inspection result normal? YES >> Replace 4WD control module. Refer to DLN-91, "Removal and Installation".

NO >> Repair or replace error-detected parts.

Component Inspection

1.CHECK ELECTRIC CONTROLLED COUPLING (RH) TEMPERATURE SENSOR

1. Turn the ignition switch OFF.

2. Disconnect rear final drive assembly harness connector.

3. Check the resistance between transfer control fluid temperature sensor connector terminals.

Is the inspection result normal?


Is the inspection result normal? YES >> INSPECTION END

NO >> Electric controlled coupling (RH) temperature sensor is malfunctioning. Replace electric controlled coupling (RH). Refer to DLN-139, "Removal and Installation".

    P1832 TCS operation signal
    DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.DTC REPRODUCTION PROCEDURE With CONSULT-III 1. Start the engine and drive at 30 km/h (19 MPH) or more. 2. Perform self-diagnosis for ...

    P183B solenoid power supply
    DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.PRECONDITIONING If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn ignition switch OFF and wait at least 10 ...

    Other materials:

    Power supply and ground circuit
    Diagnosis Procedure 1.CHECK GROUND CONNECTION 1. Turn ignition switch OFF. 2. Check ground connection E21 and E38. Refer to Ground Inspection in GI-44, "Circuit Inspection". Is the inspection result normal? YES >> GO TO 2. NO >> Repair or replace ground connection. ...

    Power supply and ground circuit
    Diagnosis Procedure 1.CHECK ABS ACTUATOR AND ELECTRIC UNIT (CONTROL UNIT) IGNITION POWER SUPPLY 1. Turn the ignition switch OFF. 2. Disconnect ABS actuator and electric unit (control unit) harness connector. 3. Check voltage between ABS actuator and electric unit (control unit) harness conne ...

    P17BB primary pressure solenoid
    DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.PREPARATION BEFORE WORK If another "DTC CONFIRMATION PROCEDURE" occurs just before, turn ignition switch OFF and wait for at least 10 seconds, then perform the next test. >> GO TO 2. 2.CHECK DTC DETECTION 1. S ...