Nissan Juke Service and Repair Manual : P181B incomplete selfshut

DTC Logic

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE


DTC CONFIRMATION PROCEDURE

1.PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn ignition switch OFF and wait at least 10 seconds before conducting the next test.

>> GO TO 2.

2.DTC REPRODUCTION PROCEDURE

1. Turn the ignition switch OFF.With CONSULT-III


1. Turn the ignition switch OFF.

2. Perform self-diagnosis for “ALL MODE AWD/4WD”.

Is DTC “P181B” detected? YES >> Proceed to diagnosis procedure. Refer to DLN-47, "Diagnosis Procedure".

NO >> INSPECTION END

Diagnosis Procedure

1.CHECK 4WD CONTROL MODULE POWER SUPPLY (1)

1. Turn the ignition switch OFF.

2. Disconnect 4WD control module harness connector.

3. Check the voltage between 4WD control module harness connector and ground.

4. Turn the ignition switch ON.


4. Turn the ignition switch ON.

CAUTION:
Never start the engine

.

5. Check the voltage between 4WD control module harness connector and ground.

Is the inspection result normal?


Is the inspection result normal? YES >> GO TO 3.

NO >> GO TO 2.

2.CHECK 4WD CONTROL MODULE POWER SUPPLY (2)

1. Turn the ignition switch OFF.

2. Check the 10A fuse (#33).

3. Check the harness for open or short between 4WD control module harness connector No.1 terminal and 10A (#33).

Is the inspection result normal?

YES >> Perform the trouble diagnosis for power supply circuit. Refer to PG-10, "Wiring Diagram - BATTERY POWER SUPPLY -".

NO >> Repair or replace error-detected parts.

3.CHECK 4WD CONTROL MODULE GROUND

1. Turn the ignition switch OFF.

2. Check the continuity between 4WD control module harness connector and ground.

Is the inspection result normal?


Is the inspection result normal? YES >> GO TO 4.

NO >> Repair or replace error-detected parts.

4.CHECK TERMINALS AND HARNESS CONNECTORS

Check 4WD control module pin terminals for damage or loose connection with harness connector.

Is inspection result normal? YES >> After turning the ignition switch OFF, perform DTC confirmation procedure again. When DTC “P181B” is detected, Replace 4WD control module. Refer to DLN-91, "Removal and Installation".

NO >> Repair or replace error-detected parts.

    P1813 4WD mode switch
    DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.PRECONDITIONING If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn ignition switch OFF and wait at least 10 ...

    P181D engine torque signal
    DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.PRECONDITIONING If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn ignition switch OFF and wait at least 10 ...

    Other materials:

    Operation
    Switch Name and Function OPERATION AND DISPLAY A/C Display (Display in Multi Display Unit) • Air conditioning system operation status is indicated on display in multi display unit. Indication of air conditioning system varies according to display mode of multi display unit. For changing pr ...

    5TH main gear assembly
    Removal and Installation REMOVAL 1. Shift the shifter lever to the 3rd gear position. 2. Disconnect the shifter cable and the selector cable from shifter lever A and selector lever. Refer to TM-25, "Removal and Installation". CAUTION: Never move shifter lever A and the selector l ...

    P0190 FRP sensor
    DTC Logic DTC DETECTION LOGIC Diagnosis Procedure 1.CHECK GROUND CONNECTIONS 1. Turn ignition switch OFF. 2. Check ground connection E38. Refer to Ground inspection in GI-44, "Circuit Inspection". Is the inspection result normal? YES >> GO TO 2. NO >> Repair or ...