Nissan Juke Service and Repair Manual : P1813 4WD mode switch

DTC Logic

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE


DTC CONFIRMATION PROCEDURE

1.PRECONDITIONING

If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn ignition switch OFF and wait at least 10 seconds before conducting the next test.

>> GO TO 2.

2.DTC REPRODUCTION PROCEDURE

1. Turn the ignition switch OFF to ON.With CONSULT-III


1. Turn the ignition switch OFF to ON.

2. Turn the 4WD mode switch 2WD⇒4WD-V⇒4WD⇒4WD-V⇒4WD.

3. Perform self-diagnosis for “ALL MODE AWD/4WD”.

Is DTC “P1813” detected? YES >> Proceed to diagnosis procedure. Refer to DLN-44, "Diagnosis Procedure".

NO >> INSPECTION END

Diagnosis Procedure

1.CHECK 4WD MODE SWITCH

Check 4WD mode switch. Refer to DLN-45, "Component Inspection".

Is the inspection result normal? YES >> GO TO 2.

NO >> Replace 4WD mode switch. Refer to DLN-92, "Removal and Installation".

2.CHECK 4WD MODE SWITCH CIRCUIT (1)

1. Disconnect 4WD control module harness connector.

2. Check the continuity between 4WD control module harness connector and 4WD mode switch harness connector.

Is the inspection result normal?


Is the inspection result normal? YES >> GO TO 3.

NO >> Repair or replace error-detected parts.

3.CHECK 4WD MODE SWITCH CIRCUIT (2)

Check the continuity between 4WD mode switch harness connector and ground.

Is the inspection result normal?


Is the inspection result normal? YES >> GO TO 4.

NO >> Repair or replace error-detected parts.

4.CHECK TERMINALS AND HARNESS CONNECTORS

• Check 4WD control module pin terminals for damage or loose connection with harness connector.

• Check 4WD mode switch pin terminals for damage or loose connection with harness connector.

Is the inspection result normal? YES >> Replace 4WD control module. Refer to DLN-91, "Removal and Installation".

NO >> Repair or replace error-detected parts.

Component Inspection

1.CHECK 4WD MODE SWITCH

1. Turn the ignition switch OFF.

2. Remove 4WD mode switch. Refer to DLN-92, "Removal and Installation".

3. Check the continuity between 4WD mode switch harness connector terminals.

Is the inspection result normal?


Is the inspection result normal? YES >> INSPECTION END

NO >> Replace 4WD mode switch. Refer to DLN-92, "Removal and Installation".

    P1811 power supply circuit for 4wd control module
    DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.PRECONDITIONING If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn ignition switch OFF and wait at least 10 ...

    P181B incomplete selfshut
    DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.PRECONDITIONING If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn ignition switch OFF and wait at least 10 ...

    Other materials:

    Luggage room lamp circuit
    Description Controls the luggage room lamp (ground side) to turn the luggage room lamp ON and OFF. Diagnosis Procedure CAUTION: Before performing the diagnosis, check that the following are normal. • Interior room lamp power supply • Luggage room lamp bulb 1.CHECK LUGGAGE ROOM LAMP OUTPUT ...

    Diagnosis and repair workflow
    Work Flow OVERALL SEQUENCE DETAILED FLOW 1.INTERVIEW FOR MALFUNCTION Interview the symptom to the customer. >> GO TO 2. 2.SYMPTOM CHECK Check the symptom from the customer's information. >> GO TO 3. 3.BASIC INSPECTION Check the operation of each part. Check that any s ...

    Vacuum lines
    MR16DDT : Removal and Installation REMOVAL 1. Remove the vacuum hose and vacuum piping. 2. Perform inspection after removal. Refer to BR-115, "MR16DDT : Inspection". INSTALLATION Note the following, install the vacuum hose. • When installing vacuum hose, insert it until its tip r ...