Nissan Juke Service and Repair Manual : P1777 step motor

DTC Logic

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE


DTC CONFIRMATION PROCEDURE

CAUTION:
Always drive vehicle at a safe speed.

NOTE:

If “DTC CONFIRMATION PROCEDURE” has been previously performed, always turn ignition switch OFF and wait at least 10 seconds before performing the next test.

After the repair, perform the following procedure to confirm the malfunction is eliminated.

1.CHECK DTC DETECTION

1. Turn ignition switch ON.With CONSULT-III


1. Turn ignition switch ON.

2. Drive vehicle for at least 5 consecutive seconds.

3. Select “Self Diagnostic Results” in “TRANSMISSION”.

Follow the procedure “With CONSULT-III”.With GST


Follow the procedure “With CONSULT-III”.

Is “P1777” detected? YES >> Go to TM-250, "Diagnosis Procedure".

NO >> Check intermittent incident. Refer to GI-42, "Intermittent Incident".

Diagnosis Procedure

1.CHECK INPUT SIGNALS

1. Start engine.With CONSULT-III


1. Start engine.

2. Select “DATA MONITOR”.

3. Start vehicle and read out the value of “STM STEP”, “SMCOIL A”, “SMCOIL B”, “SMCOIL C”, and “SMCOIL D”.

Is the inspection result normal?


Is the inspection result normal? YES >> GO TO 4.

NO >> GO TO 2.

2.CHECK HARNESS BETWEEN TCM AND STEP MOTOR

1. Turn ignition switch OFF.

2. Disconnect CVT unit harness connector and TCM connector.

3. Check continuity between TCM connector terminals and CVT unit harness connector terminals.

4. If OK, check harness for short to ground and short to power.


4. If OK, check harness for short to ground and short to power.

5. If OK, check continuity between body ground and transaxle assembly.

6. Reinstall any part removed.

Is the inspection result normal? YES >> GO TO 3.

NO >> Repair or replace damaged parts.

3.CHECK STEP MOTOR

Check step motor. Refer to TM-251, "Component Inspection".

Is the inspection result normal? YES >> GO TO 4.

NO >> Repair or replace damaged parts.

4.CHECK TCM

Check TCM input/output signals. Refer to TM-164, "Reference Value".

Is the inspection result normal? YES >> Check intermittent incident. Refer to GI-42, "Intermittent Incident".

NO >> Replace the TCM. Refer to TM-280, "Removal and Installation".

Component Inspection

STEP MOTOR

1.STEP MOTOR

1. Turn ignition switch OFF.

2. Disconnect CVT unit harness connector.

3. Check resistance between CVT unit harness connector terminals and ground.

Is the inspection result normal?


Is the inspection result normal? YES >> INSPECTION END

NO >> Replace the transaxle assembly. Refer to TM-301, "Removal and Installation".

    P1745 line pressure control
    Description The line pressure solenoid valve regulates the oil pump discharge pressure to suit the driving condition in response to a signal sent from the TCM. DTC Logic DTC DETECTION LOGIC D ...

    P1778 step motor
    Description • The step motor's 4 aspects of ON/OFF change according to the signal from TCM. As a result, the flow of line pressure to primary pulley is changed and pulley ratio is controlled. • T ...

    Other materials:

    Front oil seal
    FRONT OIL SEAL : Removal and Installation REMOVAL 1. Remove the following parts. • Front fender protector (RH): Refer to EXT-22, "Exploded View". • Drive belt: Refer to EM-20, "Exploded View". • Crankshaft pulley: Refer to EM-67, "Exploded View". 2. Remove front ...

    Vacuum lines
    MR16DDT : Exploded View 1. Clamp 2. Vacuum hose A 3. Vacuum piping 4. Vacuum hose B A. To engine side B. Paint mark C. To brake booster MR16DDT : Removal and Installation REMOVAL 1. Remove air duct and air cleaner case. Refer to EM-161, "Removal and Installation". 2. Remov ...

    Location of plastic parts
    Precautions for Plastics CAUTION: • When repairing and painting a portion of the body adjacent to plastic parts, consider their characteristics (influence of heat and solvent) and remove them if necessary or take suitable measures to protect them. • Plastic parts should be repaired and pai ...