Nissan Juke Service and Repair Manual : P1701 TCM

Description

When the power supply to the TCM is cut OFF, for example because the battery is removed, and the self-diagnosis memory function stops, malfunction is detected.

NOTE

:
Since “P1701” will be indicated when replacing TCM, perform diagnosis after erasing “SELF-DIAG RESULTS”

DTC Logic

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE


DTC CONFIRMATION PROCEDURE

NOTE

:
If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn ignition switch OFF and wait at least 10 seconds before conducting the next test.

After the repair, perform the following procedure to confirm the malfunction is eliminated.

1.CHECK DTC DETECTION

1. Turn ignition switch ON.With CONSULT-III


1. Turn ignition switch ON.

2. Wait for at least 2 consecutive seconds.

3. Select “Self Diagnostic Results” in “TRANSMISSION”.

Is “P1701” detected? YES >> Go to TM-239, "Diagnosis Procedure".

NO >> Check intermittent incident. Refer to GI-42, "Intermittent Incident".

Diagnosis Procedure

1.CHECK TCM POWER SOURCE

Check voltage between TCM connector terminals and ground.

Is the inspection result normal?


Is the inspection result normal? YES >> GO TO 4.

NO >> GO TO 2.

2.DETECT MALFUNCTIONING ITEM

Check the following.

• Harness for short or open between battery and TCM connector terminal 47 • Harness for short or open between ignition switch and TCM connector terminal 46, 48
• 10A fuse (No. 55, located in the IPDM E/R) • 10A fuse (No. 33, located in the J/B) • Ignition switch. Refer to PG-15, "Wiring Diagram - IGNITION POWER SUPPLY -".

Is the inspection result normal? YES >> GO TO 3.

NO >> Repair or replace damaged parts.

3.CHECK TCM GROUND CIRCUIT

1. Turn ignition switch OFF.

2. Disconnect TCM connector.

3. Check continuity between TCM connector terminals and ground.

Is the inspection result normal?


Is the inspection result normal? YES >> GO TO 4.

NO >> Repair or replace damaged parts.

4.CHECK TCM

Check TCM input/output signals. Refer to TM-164, "Reference Value".

Is the inspection result normal? YES >> Check intermittent incident. Refer to GI-42, "Intermittent Incident".

NO >> Replace the TCM. Refer to TM-280, "Removal and Installation".

    P1585 G sensor
    Description • G sensor is installed to floor under instrument lower cover. • G sensor detects longitudinal G and inclination that affects the vehicle and outputs to ECM using analog voltage. EC ...

    P1705 TP sensor
    Description Electric throttle control actuator consists of throttle control motor, accelerator pedal position sensor, throttle position sensor etc. The actuator sends a signal to the ECM, and ECM ...

    Other materials:

    Air cleaner and air duct
    Exploded View 1. Turbocharger air inlet pipe 2. Clamp 3. Air duct (suction) 4. Air mass flow sensor 5. O-ring 6. Air duct (inlet) 7. Grommet 8. Air cleaner case 9. Air cleaner filter 10. Cover 11. Holder A. : To turbocharger : Vehicle front : N·m (kg-m, in-lb) : Always replac ...

    Brake master cyl
    Exploded View 2WD 1. Reservoir cap 2. Oil strainer 3. Reservoir tank 4. Cylinder body 5. Pin 6. O-ring 7. Grommet : Apply polyglycol ether based lubricant. : Apply brake fluid. : N·m (kg-m, ft-lb) : Always replace after every disassembly. 4WD 1. Reservoir cap 2. Oil strai ...

    Precaution Necessary for Steering Wheel Rotation after Battery Disconnect
    NOTE: • Before removing and installing any control units, first turn the ignition switch to the LOCK position, then disconnect both battery cables. • After finishing work, confirm that all control unit connectors are connected properly, then re-connect both battery cables. • Always use CONS ...