Nissan Juke Service and Repair Manual : P0740 torque converter
DTC Logic
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
CAUTION:
Be careful of the driving speed.
1.PREPARATION BEFORE OPERATION (PART 1)
If another "DTC CONFIRMATION PROCEDURE" occurs just before, turn ignition switch OFF and wait for at least 10 seconds, then perform the next test.
>> GO TO 2.
2.PREPARATION BEFORE OPERATION (PART 2)
With CONSULT-III
1. Start the engine.
2. Select “Data Monitor” in “TRANSMISSION”.
3. Select “FLUID TEMP”.
4. Confirm that the CVT fluid temperature is in the following range.
FLUID TEMP : 10°C (50°F) or more
With GST
1. Start the engine.
2. Set the CVT fluid to 10°C (50°F) or more.
NOTE
:
When the ambient temperature is 20°C (68°F), the CVT fluid usually increases to
50 to 80°C (122 to
176°F) with driving in an urban area for approximately 10 minutes.
Is the CVT fluid 10°C (50°F) or more? YES >> GO TO 3.
NO >> 1. Warm the transaxle.
2. GO TO 3.
3.CHECK DTC DETECTION
1. Drive the vehicle.
2. Maintain the following conditions for 10 seconds or more.
Selector lever : “D” position Vehicle speed : 40 km/h (25 MPH) or more
3. Stop the vehicle.
4. Check the first trip DTC.
Is “P0740” detected? YES >> Go to TM-417, "Diagnosis Procedure".
NO >> INSPECTION END
Diagnosis Procedure
1.CHECK CIRCUIT BETWEEN TCM AND CVT UNIT
1. Turn ignition switch OFF.
2. Disconnect the TCM connector and the CVT unit connector.
3. Check the continuity between the TCM harness connector terminal and the CVT unit harness connector terminal.
Is the check result normal? YES >> GO TO 2.
NO >> Repair or replace the malfunctioning parts.
2.CHECK TORQUE CONVERTER CLUTCH SOLENOID VALVE
Check the torque converter clutch solenoid valve. Refer to TM-417, "Component Inspection (Torque Converter Clutch Solenoid Valve)".
Is the check result normal? YES >> Check intermittent incident. Refer to GI-42, "Intermittent Incident".
NO >> Repair or replace the malfunctioning parts.
Component Inspection (Torque Converter Clutch Solenoid Valve
1.CHECK TORQUE CONVERTER CLUTCH SOLENOID VALVE
Check the resistance between the CVT unit connector terminal and ground.
Is the inspection result normal? YES >> INSPECTION END
NO >> There is a malfunction of the torque converter clutch solenoid valve. Replace the transaxle assembly. Refer to TM-508, "Removal and Installation".
P0720 output speed sensor
DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE CAUTION: Be careful of the driving speed. 1.PREPARATION BEFORE WORK If another "DTC CONFIRMATION PROCEDURE" occurs just befor ...P0743 torque converter
DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE CAUTION: Be careful of the driving speed. 1.PREPARATION BEFORE OPERATION (PART 1) If another "DTC CONFIRMATION PROCEDURE" occ ...Other materials:
Fuel tank
2WD : Exploded View
1. Fuel filler cap
2. Grommet
3. Fuel filler tube
4. EVAP canister hose
5. Fuel tank mounting band (RH)
6. Fuel tank mounting band (LH)
7. Fuel tank
8. Clamp
9. Fuel filler hose
10. Vent hose
Vehicle front
: N?·m (kg-m, ft-lb)
2WD : Removal and Installation
...
Booster seats
Precautions on booster seats
WARNING
If a booster seat and seat belt are not used properly, the risk of a child
being injured in a sudden stop or collision greatly increases:
• Make sure the shoulder portion of the belt is away from the child’s face
and neck and the lap portion of the belt do ...
Operation inspection
Work Procedure
The purpose of the operational check is to check that the individual system
operates normally.
Check condition : Engine running at normal operating temperature.
1.CHECK MEMORY FUNCTION
1. Set temperature to 30°C by operating the temperature control dial.
2. Press OFF switch.
3 ...