Nissan Juke Service and Repair Manual : P0725 engine speed

Description

The engine speed signal is transmitted from ECM to TCM by CAN communication line.

DTC Logic

DTC DETECTION LOGI

DTC CONFIRMATION PROCEDURE


DTC CONFIRMATION PROCEDURE

CAUTION:
Always drive vehicle at a safe speed.

NOTE:

If “DTC CONFIRMATION PROCEDURE” has been previously performed, always turn ignition switch OFF and wait at least 10 seconds before performing the next test.

After the repair, perform the following procedure to confirm the malfunction is eliminated.

1.CHECK DTC DETECTION

1. Turn ignition switch ON.With CONSULT-III


1. Turn ignition switch ON.

2. Select “DATA MONITOR” in “TRANSMISSION”.

3. Start engine and maintain the following conditions for at least 10 consecutive seconds.

PRI SPEED SEN : More than 1000 rpm

Is “P0725” detected? YES >> Go to TM-212, "Diagnosis Procedure".

NO >> Check intermittent incident. Refer to GI-42, "Intermittent Incident".

Diagnosis Procedure

1. CHECK DTC WITH ECM

1. Turn ignition switch ON.With CONSULT-III


1. Turn ignition switch ON.

2. Select “SELF-DIAG RESULTS” in “ENGINE”.

Is the inspection result normal? YES >> GO TO 2.

NO >> Check the DTC detected item. Refer to EC-83, "CONSULT-III Function".

2. CHECK DTC WITH TCM

Select “SELF-DIAG RESULTS” in “TRANSMISSION”.With CONSULT-III


Select “SELF-DIAG RESULTS” in “TRANSMISSION”.

Is the inspection result normal? YES >> GO TO 3.

NO >> Check the DTC detected item. Refer to TM-159, "CONSULT-III Function (TRANSMISSION)".

3. CHECK INPUT SIGNALS

1. Start engine.With CONSULT-III


1. Start engine.

2. Select “DATA MONITOR” in “TRANSMISSION”.

3. While monitoring “ENG SPEED SIG”, check for engine speed change corresponding to “ACC PEDAL OPEN”.

Is the inspection result normal?


Is the inspection result normal? YES >> GO TO 4.

NO >> Check ignition signal circuit. Refer to EC-414, "Component Function Check".

4. CHECK TCM

Check TCM input/output signals. Refer to TM-164, "Reference Value".

Is the inspection result normal? YES >> Check intermittent incident. Refer to GI-42, "Intermittent Incident".

NO >> Replace the TCM. Refer to TM-280, "Removal and Installation".

    P0720 output speed sensor
    DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE CAUTION: Always drive vehicle at a safe speed. NOTE: If “DTC CONFIRMATION PROCEDURE” has been previously performed, always turn ignit ...

    P0730 incorrect gear ratio
    Description TCM selects the gear ratio using the engine load (throttle position), the primary pulley revolution speed, and the secondary pulley revolution speed as input signal. Then it changes th ...

    Other materials:

    Door mirror system (with intelligent key)
    LHD LHD : Wiring Diagram For connector terminal arrangements, harness layouts, and alphabets in a (option abbreviation; if not described in wiring diagram), refer to GI-12, "Connector Information/Explanation of Option Abbreviation". RHD RHD : Wiring Diagram For connector termina ...

    Main power supply and ground circuit
    Diagnosis Procedure 1.CHECK TCM POWER CIRCUIT 1 1. Turn the ignition switch OFF. 2. Disconnect the TCM connector. 3. Check the voltage between the TCM harness connector terminals and ground. Is the inspection result normal? YES >> GO TO 2. NO >> GO TO 4. 2.CHECK TCM POWER C ...

    Wheels
    Wash the wheels when washing the vehicle to maintain their appearance. • Clean the inner side of the wheels when the wheel is changed or the underside of the vehicle is washed. • Inspect wheel rims regularly for dents or corrosion. Such damage may cause loss of pressure or poor seal at the tir ...