Nissan Juke Service and Repair Manual : P0705 transmission range switch A
DTC Logic
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
CAUTION:
Always drive vehicle at a safe speed.
NOTE
:
If “DTC CONFIRMATION PROCEDURE” has been previously performed, always turn
ignition switch
OFF and wait at least 10 seconds before performing the next test.
After the repair, perform the following procedure to confirm the malfunction is eliminated.
1.CHECK DTC DETECTION
With CONSULT-III
1. Turn ignition switch ON.
2. Select “DATA MONITOR”.
3. Start engine.
4. Drive vehicle and maintain the following conditions for at least 2 consecutive seconds.
VEHICLE SPEED : More than 10 km/h (6 MPH) ENG SPEED : More than 450 rpm ACC PEDAL OPEN : More than 1.0/8
With GST
Follow the procedure “With CONSULT-III”.
Is “P0705” detected? YES >> Go to TM-200, "Diagnosis Procedure".
NO >> Check intermittent incident. Refer to GI-42, "Intermittent Incident".
Diagnosis Procedure
1. CHECK HARNESS BETWEEN TCM AND TRANSMISSION RANGE SWITCH
1. Turn ignition switch OFF.
2. Disconnect TCM connector and transmission range switch connector.
3. Check continuity between TCM connector terminals and transmission range switch connector terminals.
4. If OK, check harness for short to ground and short to power.
5. Reinstall any part removed.
Is the inspection result normal? YES >> GO TO 2.
NO >> Repair or replace damaged parts.
2. DETECT MALFUNCTIONING ITEM
Check the following items.
• Harness for short or open between ignition switch and transmission range switch.
• 10A fuse (No. 55, located in the IPDM E/R).
• Ignition switch.
Is the inspection result normal? YES >> GO TO 3.
NO >> Repair or replace damaged parts.
3. CHECK TRANSMISSION RANGE SWITCH
Check transmission range switch. Refer to TM-201, "Component Inspection".
Is the inspection result normal? YES >> GO TO 4.
NO >> Repair or replace damaged parts.
4.CHECK TCM
Check TCM input/output signals. Refer to TM-164, "Reference Value".
Is the inspection result normal? YES >> Check intermittent incident. Refer to GI-42, "Intermittent Incident".
NO >> Replace the TCM. Refer to TM-280, "Removal and Installation".
Component Inspection
1.CHECK TRANSMISSION RANGE SWITCH
Check continuity between transmission range switch connector terminals.
Is the inspection result normal? YES >> INSPECTION END
NO >> GO TO 2.
2.CHECK CVT POSITION
1. Disconnect control cable.
2. Check transmission range switch. (Refer to step 1 above.) Is the inspection result normal? YES >> Adjust CVT position. Refer to TM-194, "Inspection and Adjustment".
NO >> GO TO 3.
3.CHECK TRANSMISSION RANGE SWITCH
1. Remove transmission range switch. Refer to TM-278, "Removal and Installation".
2. Check transmission range switch. (Refer to step 1 above.) Is the inspection result normal? YES >> Adjust transmission range switch. Refer to TM-278, "Inspection and Adjustment".
NO >> Replace transmission range switch. Refer to TM-278, "Removal and Installation".
P0703 brake switch B
Description BCM detects ON/OFF state of the stop lamp switch and transmits the data to the CVT control unit via CAN communication by converting the data to a signal. DTC Logic DTC DETECTION LOGI ...P0710 transmission fluid temperature sensor A
DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE CAUTION: Always drive vehicle at a safe speed. NOTE: If “DTC CONFIRMATION PROCEDURE” has been previously performed, always turn ignit ...Other materials:
Service data and specifications (SDS)
Idle Speed
*: Under the following conditions
• A/C switch: OFF
• Electric load: OFF (Lights, heater fan & rear window defogger)
• Steering wheel: Kept in straight-ahead position
Ignition Timing
*: Under the following conditions
• A/C switch: OFF
• Electric load: OFF (Lights, heater f ...
System
Intelligent key system/engine start function
INTELLIGENT KEY SYSTEM/ENGINE START FUNCTION : System Diagram
INTELLIGENT KEY SYSTEM/ENGINE START FUNCTION : System
SYSTEM DESCRIPTION
• The engine start function of Intelligent Key system makes it possible to
start and stop the engine without
us ...
Air cleaner and air duct
Exploded View
1. Mass air flow sensor
2. Gasket
3. Clamp
4. Air duct (suction side)
5. Clamp
6. Air cleaner cover assembly
7. Mounting rubber
8. Air cleaner filter
9. Air cleaner body assembly
10. Air duct with resonator
11. Grommet
12. Air duct (duct side)
13. Grommet
14. B ...