Nissan Juke Service and Repair Manual : P0560 battery voltage
DTC Logic
DTC DETECTION LOGIC
NOTE
:
When IPDM E/R DTC is indicated with DTC P0560, IPDM E/R DTC must be checked
first.
Diagnosis Procedure
1.CHECK BATTERY VOLTAGE
1. Turn ignition switch ON.
2. Check battery voltage.
Voltage: Above 11 V
Is the inspection result normal? YES >> GO TO 2.
NO >> Recharge the battery.
2.CHECK BATTERY TERMINALS
1. Turn ignition switch OFF.
2. Check battery terminals condition.
Is the inspection result normal? YES >> GO TO 3.
NO >> Repair the battery terminals.
3.CHECK BATTERY AND ALTERNATOR
Check that the proper type of battery and type of alternator are installed.
Refer to, PG-126, "Battery" and CHG-35, "Alternator".
Is the inspection result normal? YES >> GO TO 4.
NO >> Replace with a proper one.
4.CHECK ECM POWER SUPPLY CIRCUIT-I
Check the voltage between ECM harness connector and ground.
Is the inspection result normal? YES >> GO TO 8.
NO >> GO TO 5.
5.CHECK ECM POWER SUPPLY CIRCUIT-II
1. Disconnect ECM harness connector.
2. Disconnect IPDM E/R harness connector E14.
3. Check the continuity between ECM harness connector and IPDM E/R harness connector
4. Also check harness for short to ground and short to power.
Is the inspection result normal? YES >> GO TO 7.
NO >> GO TO 6.
6.DETECT MALFUNCTIONING PART
Check the following.
• Harness connectors E8, F1 • Harness for open or short between ECM and IPDM E/R
>> Repair open circuit or short to ground or short to power in harness or connectors.
7.CHECK 20A FUSE
1. Disconnect 20A fuse (No. 43) from IPDM E/R.
2. Check 20A fuse.
Is the inspection result normal? YES >> GO TO 8.
NO >> Replace 20A fuse.
8.CHECK INTERMITTENT INCIDENT
Refer to GI-42, "Intermittent Incident", ???INCIDENT SIMULATION TESTS??? and ???GROUND INSPECTION???.
Is the inspection result normal? YES >> Replace IPDM E/R.
NO >> Repair or replace.
P0544 EGT sensor 1
DTC Logic DTC DETECTION LOGIC Diagnosis Procedure 1.CHECK GROUND CONNECTIONS 1. Turn ignition switch OFF. 2. Check ground connection E38. Refer to Ground inspection in GI-44, "Circuit In ...P0564 ASCD steering switch
DTC Logic DTC DETECTION LOGIC Diagnosis Procedure 1.CHECK ASCD STEERING SWITCH CIRCUIT 1. Check ASCD steering switch circuit. ASCD steering switch>>Refer to EC-1011, "Component Fun ...Other materials:
B26E8 clutch interlock switch
DTC Logic
NOTE:
• If DTC B26E8 is displayed with DTC B210F, first perform the trouble diagnosis
for DTC B210F. Refer to
BCS-83, "DTC Logic".
• If DTC B26E8 is displayed with DTC B2110, first perform the trouble diagnosis
for DTC B2110. Refer to
BCS-84, "DTC Logic".
DT ...
Removal and installation
POWER SOCKET
Exploded View
1 : Inner socket
2 : Ring
Removal and Installation
REMOVAL
1. Remove cluster tray. Refer to IP-13, "Removal and Installation".
2. Pull out inner socket (1) by pushing the pawl (B) of the ring (2)
from the inner socket hole (square) (A).
3. Press the ...
Engine control system
Engine control system : Component Parts Location
ENGINE ROOM COMPARTMENT
1. Boost control actuator
2. Turbocharger boost control solenoid
valve
3. A/F sensor 1
4. Recirculation valve
5. EVAP canister purge volume control
solenoid valve
6. Inter cooler
7. Refrigerant pressure sensor
R ...