Nissan Juke Service and Repair Manual : P0471 exhaust gas pressure sensor 1
DTC Logic
DTC DETECTION LOGIC
NOTE
:
If DTC P0471 is displayed with DTC P0470 or P2226, first perform trouble
diagnosis for DTC P0470 or P2226.
Refer to EC-944, "DTC Logic" (P0470), EC-1002, "DTC Logic" (P2226).
Diagnosis Procedure
1.CHECK GROUND CONNECTIONS
1. Turn ignition switch OFF and wait at least 20 seconds.
2. Check ground connection E38. Refer to Ground inspection in GI-44, "Circuit Inspection".
Is the inspection result normal? YES >> GO TO 2.
NO >> Repair or replace ground connection.
2.CHECK EXHAUST GAS PRESSURE SENSOR 1 AND EXHAUST GAS PIPE INSTALLATION
Check exhaust gas pressure sensor and exhaust gas pipe for poor installation and damage.
Is the inspection result normal? YES >> GO TO 3.
NO >> Install exhaust gas pressure sensor and exhaust gas pipe properly.
3.CHECK EXHAUST GAS PRESSURE SENSOR 1 POWER SUPPLY CIRCUIT
1. Disconnect exhaust pressure sensor 1 harness connector.
2. Turn ignition switch ON.
3. Check the voltage between exhaust gas pressure sensor 1 harness connector and ground.
Is the inspection result normal? YES >> GO TO 4.
NO >> Repair open circuit or short to ground or short to power in harness or connectors.
4.CHECK EXHAUST GAS PRESSURE SENSOR 1 GROUND CIRCUIT FOR OPEN AND SHORT
1. Turn ignition switch OFF and wait at least 20 seconds.
2. Check the continuity between exhaust gas pressure sensor 1 harness connector and ECM harness connector.
3. Also check harness for short to ground and short to power.
Is the inspection result normal? YES >> GO TO 5.
NO >> Repair open circuit or short to ground or short to power in harness or connectors.
5.CHECK EXHAUST PRESSURE SENSOR 1 INPUT SIGNAL CIRCUIT FOR OPEN AND SHORT
1. Check the continuity between exhaust gas pressure sensor 1 harness connector and ECM harness connector.
2. Also check harness for short to ground and short to power.
Is the inspection result normal? YES >> GO TO 6.
NO >> Repair open circuit or short to ground or short to power in harness or connectors.
6.CHECK INTERMITTENT INCIDENT
Refer to GI-42, "Intermittent Incident".
Is the inspection result normal? YES >> Replace exhaust gas pressure sensor 1.
NO >> Repair or replace.
P0470 exhaust gas pressure sensor 1
DTC Logic DTC DETECTION LOGIC NOTE: If DTC P0470 is displayed with DTC P0651 or P2263, first perform trouble diagnosis for DTC P0651 or P2263. Refer to EC-975, "DTC Logic" (P0651), ...P047A exhaust gas pressure sensor 2
DTC Logic DTC DETECTION LOGIC NOTE: If DTC P047A is displayed with DTC P0651, first perform trouble diagnosis for DTC P0651. Refer to EC-975, "DTC Logic". Diagnosis Procedure 1.CHE ...Other materials:
Keyfob ID registration
Description
Perform the following procedure after BCM is replaced or when new keyfob ID
is registered
NOTE:
When registering the keyfob ID, perform only one procedure to simultaneously
register both ID (IMMOBILIZER
ID and keyfob ID).
Work Procedure
1.STEP 1
Close all doors.
>> GO ...
Wiring diagram
BRAKE CONTROL SYSTEM
Wiring Diagram
For connector terminal arrangements, harness layout, and alphabets in a
(option abbreviation; if not
described in wiring diagram), refer to GI-12, "Connector Information/Explanation
of Option Abbreviation".
...
Front wiper auto stop signal circuit
Component Function Check
1.CHECK FRONT WIPER (AUTO STOP) SIGNAL
CONSULT-III DATA MONITOR
1. Select “WIP AUTO STOP” of IPDM E/R data monitor item.
2. Operate the front wiper.
3. With the front wiper operation, check the monitor status.
Is the status of item normal?
YES >> Auto stop sig ...