Nissan Juke Service and Repair Manual : P0097, P0098 IAT sensor 2

DTC Logic

DTC DETECTION LOGIC

DTC CONFIRMATION PROCEDURE


DTC CONFIRMATION PROCEDURE

1.PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conducting the next test.

1. Turn ignition switch OFF and wait at least 10 seconds.

2. Turn ignition switch ON.

3. Turn ignition switch OFF and wait at least 10 seconds.

TEST CONDITION:
Before performing the following procedure, confirm that battery voltage is more than 11 V at idle.

>> GO TO 2.

2.PERFORM DTC CONFIRMATION PROCEDURE

1. Start engine and let it idle for at least 5 seconds.

2. Check 1st trip DTC.

Is 1st trip DTC detected? YES >> Proceed to EC-186, "Diagnosis Procedure".

NO >> INSPECTION END

Diagnosis Procedure

1.CHECK INTAKE AIR TEMPERATURE SENSOR 2 POWER SUPPLY CIRCUIT-I

1. Turn ignition switch OFF.

2. Disconnect turbocharger boost sensor harness connector.

3. Turn ignition switch ON.

4. Check the voltage between turbocharger boost sensor harness connector terminals.

Is the inspection result normal?


Is the inspection result normal? YES >> GO TO 2.

NO >> GO TO 4.

2.CHECK INTAKE AIR TEMPERATURE SENSOR 2 SIGNAL CIRCUIT

1. Turn ignition switch OFF.

2. Disconnect ECM harness connector.

3. Check the continuity between turbocharger boost sensor harness connector and ECM harness connector.

4. Also check harness for short to ground and short to power.


4. Also check harness for short to ground and short to power.

Is the inspection result normal? YES >> GO TO 3.

NO >> Repair or replace error-detected parts.

3.CHECK INTAKE AIR TEMPERATURE SENSOR 2

Check intake air temperature sensor 2. Refer to EC-187, "Component Inspection".

Is the inspection result normal? YES >> Check intermittent incident. Refer to GI-42, "Intermittent Incident".

NO >> Replace turbocharger boost sensor (with intake air temperature sensor 2). Refer to EM-28, "Exploded View".

4.CHECK INTAKE AIR TEMPERATURE SENSOR 2 POWER SUPPLY CIRCUIT-II

Check the voltage between turbocharger boost sensor harness connector terminal and ground.

Is the inspection result normal?


Is the inspection result normal? YES >> GO TO 5.

NO >> GO TO 7.

5.CHECK INTAKE AIR TEMPERATURE SENSOR 2 GROUND CIRCUIT

1. Turn ignition switch OFF.

2. Disconnect ECM harness connector.

3. Check the continuity between turbocharger boost sensor harness connector and ECM harness connector.

Is the inspection result normal?


Is the inspection result normal? YES >> GO TO 6.

NO >> Repair or replace error-detected parts.

6.CHECK ECM GROUND CIRCUIT

Check the continuity between ECM harness connector and ground.

Is the inspection result normal?


Is the inspection result normal? YES >> Check intermittent incident. Refer to GI-42, "Intermittent Incident".

NO >> Repair or replace error-detected parts.

7.CHECK SENSOR POWER SUPPLY CIRCUIT

1. Turn ignition switch OFF.

2. Disconnect ECM harness connectors and each sensor harness connectors 3. Check harness connector for short to power and short to ground, between the following terminals.

*1: CVT models


*1: CVT models
*2: RHD with M/T models

Is the inspection result normal? YES >> Perform the trouble diagnosis for power supply circuit.

NO >> Repair or replace error-detected parts.

Component Inspection

1.CHECK INTAKE AIR TEMPERATURE SENSOR 2

1. Turn ignition switch OFF.

2. Disconnect turbocharger boost sensor harness connector.

3. Check resistance between turbocharger boost sensor terminals as follows.

Is the inspection result normal?


Is the inspection result normal? YES >> INSPECTION END NO >> Replace turbocharger boost sensor (with intake air temperature sensor 2). Refer to EM-28, "Exploded View".

    P0087, P0088, P0090 FRP control system
    DTC Logic DTC DETECTION LOGIC NOTE: • If DTC P0087 or P0090 is displayed with DTC P1197, first perform the trouble diagnosis for DTC P1197. • DTC P0087 or P0090 may be displayed when running ou ...

    P0102, P0103 MAF sensor
    DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.PRECONDITIONING If DTC Confirmation Procedure has been previously conducted, always perform the following procedure before conductin ...

    Other materials:

    Driving on snow or ice
    WARNING • Wet ice (328F, 08C and freezing rain), very cold snow or ice can be slick and very hard to drive on. The vehicle will have much less traction or “grip” under these conditions. Try to avoid driving on wet ice until the road is salted or sanded. • Whatever the condition, drive with cau ...

    B210F shift position/clutch interlock switch
    DTC Logic DTC DETECTION LOGIC NOTE: If DTC B210F is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to PCS- 30, "DTC Logic". DTC CONFIRMATION PROCEDURE 1.PERFORM DTC CONFIRMATION PROCEDURE 1. Shift selector lever to the P position. 2. Turn ign ...

    Door motor
    Exploded View LEFT SIDE 1. A/C unit assembly 2. Intake door lever 3. Intake door motor 4. Air mix door motor 5. Upper air mix door rod 6. Upper air mix door lever 7. Lower air mix door lever 8. Lower air mix door rod RIGHT SIDE 1. A/C unit assembly 2. Main link 3. Sub defrost ...