Nissan Juke Service and Repair Manual : P0011 IVT control

DTC Logic

DTC DETECTION LOGIC

NOTE

:
If DTC P0011 is displayed with DTC P0075, first perform the trouble diagnosis for DTC P0075. Refer to EC-583, "DTC Logic".

DTC CONFIRMATION PROCEDURE


DTC CONFIRMATION PROCEDURE

1.PRECONDITIONING

If DTC Confirmation Procedure has been previously conducted, always turn ignition switch OFF and wait at least 10 seconds before conducting the next test.

TESTING CONDITION:
Before performing the following procedure, confirm that battery voltage is between 10 V and 16 V at idle.

>> GO TO 2.

2.PERFORM DTC CONFIRMATION PROCEDURE-I

1. Turn ignition switch ON and select “DATA MONITOR” mode with CONSULT-III.With CONSULT-III


1. Turn ignition switch ON and select “DATA MONITOR” mode with CONSULT-III.

2. Start engine and warm it up to the normal operating temperature.

3. Maintain the following conditions for at least 6 consecutive seconds. Hold the accelerator pedal as steady as possible.

4. Let engine idle for 10 seconds.


4. Let engine idle for 10 seconds.

5. Check 1st trip DTC.

Follow the procedure “With CONSULT-III” above.With GST


Follow the procedure “With CONSULT-III” above.

Is 1st trip DTC detected? YES >> Go to EC-571, "Diagnosis Procedure" NO >> GO TO 3.

3.PERFORM DTC CONFIRMATION PROCEDURE-II

1. Maintain the following conditions for at least 20 consecutive seconds.With CONSULT-III


1. Maintain the following conditions for at least 20 consecutive seconds.


CAUTION:


CAUTION:
Always drive at a safe speed.

2. Check 1st trip DTC.

Follow the procedure “With CONSULT-III” above.With GST


Follow the procedure “With CONSULT-III” above.

Is 1st trip DTC detected? YES >> Go to EC-571, "Diagnosis Procedure" NO >> INSPECTION END

Diagnosis Procedure

1.CHECK OIL PRESSURE WARNING LAMP

1. Start engine.

2. Check oil pressure warning lamp and confirm it is not illuminated.

Is oil pressure warning lamp illuminated? YES >> Go to LU-25, "Inspection".

NO >> GO TO 2.

2.CHECK INTAKE VALVE TIMING CONTROL SOLENOID VALVE


2.CHECK INTAKE VALVE TIMING CONTROL SOLENOID VALVE

Refer to EC-572, "Component Inspection".

Is the inspection result normal? YES >> GO TO 3.

NO >> Replace intake valve timing control solenoid valve.

3.CHECK CRANKSHAFT POSITION SENSOR (POS)

Refer to EC-658, "Component Inspection".

Is the inspection result normal? YES >> GO TO 4.

NO >> Replace crankshaft position sensor (POS).

4.CHECK CAMSHAFT POSITION SENSOR (PHASE)

Refer to EC-662, "Component Inspection".

Is the inspection result normal? YES >> GO TO 5.

NO >> Replace camshaft position sensor (PHASE).

5.CHECK CAMSHAFT (INTAKE)

Check the following.

• Accumulation of debris to the signal plate of camshaft (1) rear end • Chipping signal plate of camshaft rear end

Is the inspection result normal? YES >> GO TO 6.

NO >> Remove debris and clean the signal plate of camshaft rear end or replace camshaft.

6.CHECK TIMING CHAIN INSTALLATION

Check service records for any recent repairs that may cause timing chain misaligned.

Are there any service records that may cause timing chain misaligned? YES >> Check timing chain installation. Refer to EM-181, "Exploded View".

NO >> GO TO 7.

7.CHECK LUBRICATION CIRCUIT

Perform “Inspection of Camshaft Sprocket (INT) Oil Groove”. Refer to EM-200, "Inspection".

Is the inspection result normal? YES >> GO TO 8.

NO >> Clean lubrication line.

8.CHECK INTERMITTENT INCIDENT

Refer to GI-42, "Intermittent Incident".

>> INSPECTION END

Component Inspection

1.CHECK INTAKE VALVE TIMING CONTROL SOLENOID VALVE-I

1. Turn ignition switch OFF.

2. Disconnect intake valve timing control solenoid valve harness connector.

3. Check resistance between intake valve timing control solenoid valve terminals as follows.

Is the inspection result normal?


Is the inspection result normal? YES >> GO TO 2.

NO >> Replace intake valve timing control solenoid valve.

2.CHECK INTAKE VALVE TIMING CONTROL SOLENOID VALVE-II

1. Remove intake valve timing control solenoid valve.

2. Apply 12 V between intake valve timing control solenoid valve terminals 1 and 2, and then interrupt it. Make sure that the plunger moves as shown in the figure.

CAUTION:
Do not apply 12 V continuously for 5 seconds or more.

Doing so may result in damage to the coil in intake valve timing control solenoid valve.

NOTE:

Always replace O-ring when intake valve timing control solenoid valve is removed.

Is the inspection result normal?

YES >> INSPECTION END


YES >> INSPECTION END

NO >> Replace intake valve timing control solenoid valve.

    U1000, U1001 CAN COMM CIRCUIT
    Description CAN (Controller Area Network) is a serial communication line for real time application. It is an on-vehicle multiplex communication line with high data communication speed and excellen ...

    P0014 EVT control
    DTC Logic DTC DETECTION LOGIC NOTE: If DTC P0014 is displayed with DTC P0078, first perform trouble diagnosis for DTC P0078. Refer to EC- 585, "DTC Logic". DTC CONFIRMATION PROCEDUR ...

    Other materials:

    Camera image signal circuit
    Description • The NAVI control unit supplies power to the rear view camera when receiving a reverse signal. • The rear view camera transmits camera images to the NAVI control unit when power is supplied from the NAVI control unit. Diagnosis Procedure 1.CHECK CONTINUITY CAMERA POWER SUPPLY C ...

    Tire labeling
    Federal law requires tire manufacturers to place standardized information on the sidewall of all tires. This information identifies and describes the fundamental characteristics of the tire and also provides the tire identification number (TIN) for safety standard certification. The TIN can be ...

    B1023 passenger air bag off indicator
    DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.CHECK SELF-DIAG RESULT With CONSULT-III 1. Turn ignition switch ON. 2. Perform “Self Diagnostic Result” mode of “AIR BAG” using CONSULT-III. Without CONSULT-III 1. Turn ignition switch ON. 2. Check the air bag warning lamp statu ...