Nissan Juke Service and Repair Manual : P0001 fuel pump

DTC Logic

DTC DETECTION LOGIC

NOTE:


NOTE

:
If DTC P0001 is displayed with DTC P0560 or P0657, first perform trouble diagnosis for DTC P0560 or P0657.

Refer to EC-963, "DTC Logic" (DTC P0560) or EC-976, "DTC Logic" (DTC P0657).

Diagnosis Procedure

1.CHECK HIGH PRESSURE SUPPLY PUMP (VOLUMETRIC CONTROL VALVE) POWER SUPPLY CIRCUIT

1. Turn ignition switch OFF.

2. Disconnect high pressure supply pump (volumetric control valve) harness connector.

3. Turn ignition switch ON.

4. Check the voltage between high pressure supply pump (volumetric control valve) harness connector and ground.

Is the inspection result normal?


Is the inspection result normal? YES >> GO TO 3.

NO >> GO TO 2.

2.DETECT MALFUNCTIONING PART

Check the following.

• Harness or connectors E8, F1 • Harness for open or short between IPDM E/R and high pressure supply pump (volumetric control valve)

>> Repair open circuit or short to ground or short to power in harness or connectors.

3.CHECK HIGH PRESSURE SUPPLY PUMP (VOLUMETRIC CONTROL VALVE) OUTPUT SIGNAL CIRCUIT FOR OPEN AND SHORT

1. Turn ignition switch OFF.

2. Disconnect ECM harness connector.

3. Check the continuity between high pressure supply pump (volumetric control valve) harness connector and ECM harness connector.

4. Also check harness for short to ground and short to power.


4. Also check harness for short to ground and short to power.

Is the inspection result normal?

YES >> GO TO 4.

NO >> Repair open circuit or short to ground or short to power in harness or connectors.

4.CHECK HIGH PRESSURE SUPPLY PUMP (VOLUMETRIC CONTROL VALVE)

Refer to EC-889, "Component Inspection".

Is the inspection result normal? YES >> GO TO 5.

NO >> Replace high pressure supply pump.

5.CHECK FUEL LINE

Check fuel line cleanliness.

Is the inspection result normal? YES >> GO TO 6.

NO >> Fuel line cleanliness.

6.CHECK INTERMITTENT INCIDENT

Refer to GI-42, "Intermittent Incident", ???INCIDENT SIMULATION TESTS??? and ???GROUND INSPECTION???.

>> INSPECTION END

Component Inspection

1.CHECK HIGH PRESSURE SUPPLY PUMP (VOLUMETRIC CONTROL VALVE)

1. Turn ignition switch OFF.

2. Disconnect high pressure supply pump (volumetric control valve) harness connector.

3. Check resistance between high pressure supply pump (volumetric control valve) terminals as follows.

Is the inspection result normal?


Is the inspection result normal? YES >> INSPECTION END

NO >> Replace high pressure supply pump.

    Power supply and ground circuit
    Diagnosis Procedure 1.INSPECTION START Start engine. Is engine running? YES >> GO TO 6. NO >> GO TO 2. 2.CHECK GROUND CONNECTION-I 1. Turn ignition switch OFF. 2. Check groun ...

    P0002 fuel pump
    DTC Logic DTC DETECTION LOGIC NOTE: If DTC P0002 is displayed with DTC P0087, P0089, P0090 or P0190, first perform trouble diagnosis for DTC P0087, P0089, P0090 or P0190. Refer to EC-895, " ...

    Other materials:

    Precaution Necessary for Steering Wheel Rotation after Battery Disconnect
    NOTE: • Before removing and installing any control units, first turn the ignition switch to the LOCK position, then disconnect both battery cables. • After finishing work, confirm that all control unit connectors are connected properly, then re-connect both battery cables. • Always use CONS ...

    Diagnosis and repair workflow
    Work Flow OVERALL SEQUENCE DETAILED FLOW 1.INTERVIEW FOR MALFUNCTION Interview the symptom to the customer. >> GO TO 2. 2.SYMPTOM CHECK Check the symptom from the customer's information. >> GO TO 3. 3.BASIC INSPECTION Check the operation of each part. Check that any s ...

    Outside mirror
    Exploded View 1. Door mirror cover 2. Actuator 3. Glass mirror 4. Door mirror corner cover 5. Door mirror assembly : Clip : Pawl Door mirror assembly DOOR MIRROR ASSEMBLY : Removal and Installation CAUTION: When removing, always use a remover tool that is made of plastic. REMOVAL 1 ...