Nissan Juke Service and Repair Manual : Oil pan (lower)

Exploded View

With Oil Cooler

1. Rear oil seal


1. Rear oil seal
2. O-ring
3. Oil pan (upper)
4. Oil pump chain tensioner (for oil pump drive chain)
5. Oil pump drive chain 6. Crankshaft sprocket
7. Oil pump sprocket
8. Oil pump
9. O-ring
10. O-ring
11. Oil pan (lower)
12. Oil pan drain plug
13. Drain plug washer
14. Oil level sensor
15. Relief valve
16. Connector bolt
17. Oil filter
18. Oil cooler
19. O-ring

A. Refer to EM-182
B. Refer to LU-28
C. Oil pan (lower) side

disassembly.: Always replace after every
disassembly.

: N·m (kg-m, ft-lb): N·m (kg-m, in-lb)
: Sealing point: N·m (kg-m, ft-lb)
: Should be lubricated with oil: Sealing point
With Out Oil Cooler: Should be lubricated with oil


With Out Oil Cooler

1. Rear oil seal


1. Rear oil seal
2. O-ring
3. Oil pan (upper)
4. Oil pump chain tensioner (for oil pump drive chain)
5. Oil pump drive chain 6. Crankshaft sprocket
7. Oil pump sprocket
8. Oil pump
9. O-ring
10. O-ring
11. Oil pan (lower)
12. Oil pan drain plug
13. Drain plug washer
14. Oil level sensor
15. Oil filter stud bolt 16. Oil filter

A. Refer to EM-182
B. Refer to LU-28
C. Oil pan (lower) side

disassembly.: Always replace after every
disassembly.

: N·m (kg-m, ft-lb): N·m (kg-m, in-lb)
: Sealing point: N·m (kg-m, ft-lb)
: Should be lubricated with oil: Sealing point
Removal and Installation: Should be lubricated with oil


Removal and Installation

REMOVAL

1. Drain engine oil. Refer to CO-11, "Draining".

2. Remove oil pan (lower) with the following procedure:

a. Loosen mounting bolts in reverse order as shown in the figure.

: Engine front


b. Insert seal cutter [SST: KV10111100] (A) between oil pan (upper)


b. Insert seal cutter [SST: KV10111100] (A) between oil pan (upper) and oil pan (lower).

CAUTION:
• Be careful not to damage the mating surface.

• Never insert a screwdriver. This damages the mating surfaces.

c. Slide the seal cutter [SST: KV10111100] by tapping on the side of tool with a hammer.

d. Remove oil pan (lower).

INSTALLATION


INSTALLATION

1. Install oil pan (lower) as follows: a. Use a scraper (A) to remove old liquid gasket from mating surfaces.

• Also remove old liquid gasket from mating surface of oil pan (upper).

• Remove old liquid gasket from the bolt holes and threads.

CAUTION:
Never scratch or damage the mating surface when cleaning off old liquid gasket.

b. Apply a continuous bead of liquid gasket (B) with a tube presser


b. Apply a continuous bead of liquid gasket (B) with a tube presser (commercial service tool) as shown in the figure.

a : 7.5 - 9.5 mm (0.295 - 0.374 in) c : φ4.0 - 5.0 mm (0.157 - 0.197 in) 1 : Oil pan (lower)
Use Genuine Liquid Gasket or equivalent.: Engine outside


Use Genuine Liquid Gasket or equivalent.

CAUTION:
Attaching should be done within 5 minutes after liquid gasket application.

c. Tighten bolts in numerical order as shown in the figure.


c. Tighten bolts in numerical order as shown in the figure.

: Engine front


2. Install oil pan drain plug.


2. Install oil pan drain plug.

• Refer to the figure of components of former page for installation direction of drain plug washer. Refer to EM-169, "Exploded View".

3. Install in the reverse order of removal after this step.

NOTE

:
Wait at last 30 minutes after oil pan (lower) is installed before pouring engine oil.

Inspection

INSPECTION AFTER REMOVAL

Clean oil strainer if any object attached.

INSPECTION AFTER INSTALLATION

1. Check the engine oil level and adjust engine oil. Refer to LU-25, "Inspection".

2. Start engine, and check there is no leakage of engine oil.

3. Stop engine and wait for 10 minutes.

4. Check the engine oil level again. Refer to LU-25, "Inspection".

    Exhaust manifold
    Exploded View 1. Exhaust manifold cover 2. Harness bracket 3. Air fuel ratio sensor 1 4. Exhaust manifold stay 5. Heat insulator 6. Exhaust manifold 7. Exhaust manifold cover 8. Gasket ...

    Fuel injector and fuel tube
    Exploded View 1. Stud bolt 2. O-ring (green) 3. Fuel injector (front) 4. Clip 5. Fuel injector (rear) 6. O-ring (black) 7. Fuel tube protector 8. Fuel tube 9. Fuel feed hose 10. Qui ...

    Other materials:

    Wiring diagram
    AUDIO WITH NAVIGATION Wiring Diagram For connector terminal arrangements, harness layouts, and alphabets in a (option abbreviation; if not described in wiring diagram), refer to GI-12, "Connector Information/Explanation of Option Abbreviation". ...

    Safety note
    WARNING • Do not disassemble or modify this system. If you do, it may result in accidents, fire, or electric shock. • Do not use this system if you notice any abnormality, such as a frozen screen or lack of sound. Continued use of the system may result in accident, fire or electric shock. • ...

    Ignition position warning function does not operate
    Diagnosis Procedure 1.CHECK DTC WITH BCM Check that DTC is not detected with BCM. Is the inspection result normal? YES >> GO TO 2. NO >> Refer to BCS-67, "DTC Index". 2.CHECK POWER DOOR LOCK OPERATION Check power door lock operation. Does door lock/unlock with d ...