Luggage floor trim - Removal and installation - Interior - Nissan Juke Service and Repair Manual:

Nissan Juke Service and Repair Manual : Luggage floor trim

Nissan Juke Service and Repair Manual / Interior / Removal and installation / Luggage floor trim

Exploded View

2WD models

1. Rear pillar cap RH

1. Rear pillar cap RH 2. Luggage side upper finisher RH 3. Luggage side lower finisher RH 4. Luggage floor board
5. Luggage side upper finisher LH 6. Rear pillar cap LH
7. Luggage side lower finisher LH 8. Seat belt hook LH
9. Shock absorber mask LH 10. Luggage side lower finisher grille LH 11. Repair kit holder (Models without spare tire) 12. Luggage rear plate
13. Luggage side lower finisher grille RH 14. Luggage room lamp
15. Shock absorber mask RH 16. Seat belt hook RH
17. Luggage floor box
18. Luggage floor rear center spacer (Models with spare tire) 19. Spare tire clamp (Models with spare tire)

: Pawl Clip
: Pawl
: Metal clip
4WD models : Vehicle front

4WD models

1. Rear pillar cap RH

1. Rear pillar cap RH 2. Luggage side upper finisher RH 3. Luggage side lower finisher RH 4. Luggage floor board
5. Luggage side upper finisher LH 6. Rear pillar cap LH
7. Luggage side lower finisher LH 8. Seat belt hook LH
9. Shock absorber mask LH 10. Luggage side lower finisher grille LH 11. Luggage floor rear spacer LH 12. Luggage rear plate
13. Luggage side lower finisher grille RH 14. Luggage room lamp
15. Shock absorber mask RH 16. Seat belt hook RH
17. Luggage floor rear spacer RH 18. Spare tire clamp

: Pawl : Clip
: Pawl
: Metal clip
Luggage rear plate : Removal and Installation Vehicle fro

Luggage rear plate : Removal and Installation

CAUTION:
• When removing, always use a remover tool that is made of plastic.

• Never damage the body.

REMOVE

1. Remove back door weather-strip.

• TYPE1: Refer to DLK-170, "BACK DOOR WEATHER-STRIP : Removal and Installation".

• TYPE2: Refer to DLK-333, "BACK DOOR WEATHER-STRIP : Removal and Installation".

• TYPE3: Refer to DLK-468, "BACK DOOR WEATHER-STRIP : Removal and Installation".

• TYPE4: Refer to DLK-584, "BACK DOOR WEATHER-STRIP : Removal and Installation".

2. Remove luggage floor board.

3. Remove luggage floor box. (Models withe 2WD) 4. Disengage luggage rear plate fixing metal clips with a remover tool (A), and then remove luggage rear plate.

: Metal clip

INSTALLATION

Note the following item, and install in the reverse order of removal.

CAUTION:
When installing luggage rear plate, check that metal clips are securely in body panel holes, and press them in.

Luggage side lower finisher : Removal and Installation

REMOVAL

CAUTION:
• When removing, always use a remover tool that is made of plastic.

• Never damage the body.

1. Remove luggage room lamp. Refer to INL-39, "Removal and Installation".

2. Remove luggage floor board.

3. Remove luggage floor box.(Models with 2WD) 4. Remove luggage rear plate. Refer to INT-30, "LUGGAGE REAR PLATE : Removal and Installation".

5. Remove rear body side welt. Refer to INT-20, "BODY SIDE WELT : Removal and Installation".

6. Remove rear seat cushion.

• 2WD models: Refer to SE-33, "SEAT CUSHION : Removal and Installation".

• 4WD models: Refer to SE-42, "SEAT CUSHION : Removal and Installation".

7. Remove rear seat back.

• 2WD models: Refer to SE-33, "SEATBACK : Removal and Installation".

• 4WD models: Refer to SE-43, "SEATBACK : Removal and Installation".

8. Remove side hinge.

• 2WD models: Refer to SE-38, "SEATBACK HINGE : Removal and Installation".

• 4WD models: Refer to SE-48, "SEATBACK HINGE : Removal and Installation".

9. Disengage luggage side lower finisher fixing clips with a remover tool (A), and then remove luggage side lower finisher.

: Clip

INSTALLATION

Note the following item, and install in the reverse order of removal.

CAUTION: When installing luggage side lower finisher, check that clips are securely in body panel holes, and press them in.

Removal and installation of shock absorber mask CAUTION: When removing, always use a remover tool that is made of plastic.

REMOVAL

Disengage shock absorber mask fixing pawls with a remover tool (A), and then remove shock absorber mask.

CAUTION: : Pawl

CAUTION: Apply protective tape (B) on the parts to protect it from damage.

INSTALLATION

Install in the reverse order of removal.

Removal and installation of luggage side lower finisher grille CAUTION: When removing, always use a remover tool that is made of plastic.

REMOVAL

Disengage luggage side lower finisher grille fixing pawls with a remover tool (A), and then remove luggage side lower finisher grille.

CAUTION: : Pawl

CAUTION: Apply protective tape (B) on the parts to protect it from damage.

INSTALLATION

Install in the reverse order of removal.

CAUTION:
• When removing, always use a remover tool that is made of plastic.

• Never damage the body.

1. Remove luggage side lower finisher. Refer to INT-31, "LUGGAGE SIDE LOWER FINISHER : Removal and Installation".

2. Remove rear seat belt (floor) anchor bolt. Refer to SB-12, "SEAT BELT RETRACTOR : Removal and Installation".

3. Disengage luggage side upper finisher fixing clips and metal clips with a remover tool (A), and then remove luggage side upper finisher.

: Clip
: Metal clip

INSTALATION

Note the following item, and install in the reverse order of removal.

CAUTION:
When installing luggage side upper finisher, check that clips, and metal clips are securely in body panel holes, and press them in.

Headlining

Exploded View LHD models 1. Headlining assembly 2. Assist grip clip 3. Rear assist grip RH 4. Front assist grip RH 5. Sun visor assembly RH 6. Sun visor cover RH 7. Sun visor cover LH ...

Back door trim

Exploded View 1. Back door side finisher RH 2. Rear parcel shelf finisher 3. Back door side finisher LH 4. Back door lower finisher 5. Emergency lid 6. Back door pull handle : Clip : Paw ...

Other materials:

U1010 control unit (can)
Description CAN (Controller Area Network) is a serial communication line for real time application. It is an on-vehicle multiplex communication line with high data communication speed and excellent error detection ability. Many electronic control units are equipped onto a vehicle, and each co ...

Component parts
Component Parts Location LHD models 1. Multi display unit* Refer to DMS-3, "Component Parts Location". 2. ABS actuator and electric unit (control unit) Refer to BRC-9, "Component Parts Location" (without ESP), BRC-97, "Component Parts Location" (with ESP). ...

Seats, seat belts and Supplemental Restraint System (SRS)
1. Rear head restraints 2. Child restraint anchor points (for top tether strap child restraint) 3. Front head restraints — Front-seat Active Head Restraints 4. Roof-mounted curtain side-impact supplemental air bags 5. Seat belts 6. Front seats 7. Supplemental front-impact air bags ...