Nissan Juke Service and Repair Manual : Lubricant

Description

MAINTENANCE OF LUBRICANT LEVEL

The compressor lubricant is circulating in the system together with the refrigerant. It is necessary to fill compressor with lubricant when replacing A/C system parts or when a large amount of refrigerant leakage is detected. It is important to always maintain lubricant level within the specified level. Otherwise, the following conditions may occur.

• Insufficient lubricant amount: Stuck compressor • Excessive lubricant amount: Insufficient cooling (caused by insufficient heat exchange)

Name : A/C system Oil Type R

Inspection

If a compressor is malfunctioning (internal noise, insufficient cooling), check the compressor oil.

1.COMPRESSOR OIL JUDGMENT

1. Remove the compressor. Refer to HA-87, "COMPRESSOR : Removal and Installation".

2. Sample a compressor oil and judge on the figure.

Judgement result 1>>Replace compressor only.


Judgement result 1>>Replace compressor only.

Judgement result 2>>Replace compressor and liquid tank.

Perform Lubricant Return Operation

CAUTION:
If a large amount of refrigerant or lubricant leakage is detected, never perform lubricant return operation.

1. Start the engine and set to the following conditions.

• Engine speed: Idling to 1,200 rpm • A/C switch: ON
• Fan speed: Maximum speed set • Intake door position: Recirculation • Temperature setting: Full cold

2. Perform lubricant return operation for approximately 10 minutes.

3. Stop the engine.

4. Lubricant return operation is complete.

Lubricant Adjusting Procedure for Components Replacement Except Compressor

Fill with lubricant for the amount that is calculated according to the following conditions.

Example: Lubricant amount to be added when replacing evaporator and liquid tank [m (Imp fl oz.)] = 35 (1.2) + 5 (0.2) + α

Lubricant Adjusting Procedure for Compressor Replacement


Lubricant Adjusting Procedure for Compressor Replacement

1. Drain lubricant from removed compressor and measure lubricant amount.

1. Drain lubricant from high-pressure port (A) and low-pressure port (B) while rotating magnet clutch.

2. Measure total amount of lubricant that is drained from removed compressor.

2. Drain lubricant from a new compressor that is calculated according


2. Drain lubricant from a new compressor that is calculated according to the following conditions.

Amount to be drained (A) [m (Imp fl oz.)] = F − (D + S + R + α)
F : Lubricant amount that a new compressor contains [120 (4.2)]
D : Lubricant amount that is drained from removed compressor
S : Lubricant amount that remains inside of removed compressor [20 (0.7)]
R : Lubricant amount to be added according to components that are removed except compressor α : Lubricant amount that is recycled together with refrigerant during recycle operation

CAUTION:


CAUTION:
If lubricant amount that is drained from removed compressor is less than 60 m (2.1 Imp fl oz.), perform calculation by setting “D” as 40 m (1.4 Imp fl oz.).

Example: Lubricant amount to be drained from a new compressor when replacing


Example: Lubricant amount to be drained from a new compressor when replacing compressor and liquid tank [m (Imp fl oz.)] [D = 60 (2.1), α = 5 (0.2)] 120 (4.2) − [60 (1.6) + 20 (0.7) + 5 (0.2) + 5 (0.2)] = 30 (1.0)

3. Install compressor and check the operation.

    Refrigerant
    Description CONNECTION OF SERVICE TOOLS AND EQUIPMENT 1. Shut-off valve 2. A/C service valve 3. Recovery/recycling/recharging equipment 4. Vacuum pump 5. Manifold gauge set 6. Refrigeran ...

    Performance test
    Inspection INSPECTION PROCEDURE 1. Connect recovery/recycling/recharging equipment (for HFC-134a) or manifold gauge. 2. Start the engine, and set to the following condition. Test condition ...

    Other materials:

    P1641 thermoplunger control unit
    DTC Logic DTC DETECTION LOGIC Diagnosis Procedure 1.CHECK THERMOPLUNGER CONTROL UNIT POWER SUPPLY CIRCUIT 1. Turn ignition switch OFF. 2. Disconnect thermoplunger control unit harness connector. 3. Check the voltage between thermoplunger control unit harness connector and ground. Is the ...

    Shift P warning lamp
    Component Function Check 1.CHECK FUNCTION 1. Select “INTELLIGENT KEY” of “BCM” using CONSULT-III. 2. Select “LCD” in “ACTIVE TEST” mode. 3. Check that the function operates normally according to the following conditions. Is the inspection result normal? YES >> Shift P warning lamp is ...

    Diagnosis system (navi control unit)
    Diagnosis Description On-Board Diagnosis Item • On-board diagnosis is performed in service test mode. • On-board diagnosis checks if the system operates normally. Service test mode METHOD OF STARTING 1. Start the engine. 2. Turn OFF audio. 3. While pressing the “SET UP” switch, turn th ...