Nissan Juke Service and Repair Manual : License plate lamp circuit
Without daytime running light system
WITHOUT DAYTIME RUNNING LIGHT SYSTEM : Component Function Check
1.CHECK TAIL LAMP (RH) OPERATION
Check that the tail lamp (RH) is turned ON.
Is the inspection result normal? YES >> GO TO 2.
NO >> Check tail lamp circuit. Refer to EXL-61, "WITHOUT DAYTIME RUNNING LIGHT SYSTEM : Component Function Check".
2.CHECK LICENSE PLATE LAMP OPERATION
CONSULT-III ACTIVE TEST
1. Select “EXTERNAL LAMPS” of IPDM E/R active test item.
2. With operating the lighting switch, check that the license plate lamp is turned ON.
TAIL : License plate lamp ON Off : License plate lamp OFF
Is the inspection result normal? YES >> License plate lamp circuit is normal.
NO >> Refer to EXL-65, "WITHOUT DAYTIME RUNNING LIGHT SYSTEM : Diagnosis Procedure".
WITHOUT DAYTIME RUNNING LIGHT SYSTEM : Diagnosis Procedure
1.CHECK LICENSE PLATE LAMP BULB
Check the applicable lamp bulb.
Is the inspection result normal? YES >> GO TO 2.
NO >> Replace bulb.
2.CHECK LICENSE PLATE LAMP OPEN CIRCUIT
1. Turn ignition switch OFF.
2. Disconnect IPDM E/R connector and back door opener switch connector.
3. Check continuity between IPDM E/R harness connector and back door opener switch harness connector
Is the inspection result normal? YES >> GO TO 3.
NO >> Repair or replace harness.
3.CHECK LICENSE PLATE LAMP GROUND OPEN CIRCUIT
Check continuity between back door opener switch harness connector and ground.
Is the inspection result normal? YES >> Check corresponding bulb socket and harness. Repair or replace if necessary.
NO >> Repair or replace harness
With daytime running light system
WITH DAYTIME RUNNING LIGHT SYSTEM : Component Function Check
1.CHECK TAIL LAMP (RH) OPERATION
Check that the tail lamp (RH) is turned ON.
Is the inspection result normal? YES >> GO TO 2.
NO >> Check tail lamp circuit. Refer to EXL-62, "WITH DAYTIME RUNNING LIGHT SYSTEM : Component Function Check".
2.CHECK LICENSE PLATE LAMP OPERATION
CONSULT-III ACTIVE TEST
1. Select “EXTERNAL LAMPS” of IPDM E/R active test item.
2. With operating the lighting switch, check that the license plate lamp is turned ON.
TAIL : License plate lamp ON Off : License plate lamp OFF
Is the inspection result normal? YES >> License plate lamp circuit is normal.
NO >> Refer to EXL-66, "WITH DAYTIME RUNNING LIGHT SYSTEM : Diagnosis Procedure".
WITH DAYTIME RUNNING LIGHT SYSTEM : Diagnosis Procedure
1.CHECK LICENSE PLATE LAMP BULB
Check the applicable lamp bulb.
Is the inspection result normal? YES >> GO TO 2.
NO >> Replace bulb.
2.CHECK LICENSE PLATE LAMP OPEN CIRCUIT
1. Turn ignition switch OFF.
2. Remove daytime running light relay.
3. Disconnect back door opener switch connector.
4. Check continuity between daytime running light relay harness connector and back door opener switch harness connector.
Is the inspection result normal? YES >> GO TO 3.
NO >> Repair or replace harness.
3.CHECK LICENSE PLATE LAMP GROUND OPEN CIRCUIT
Check continuity between back door opener switch harness connector and ground.
Is the inspection result normal? YES >> Check corresponding bulb socket and harness. Repair or replace if necessary.
NO >> Repair or replace harness.
Tail lamp circuit
Without daytime running light system WITHOUT DAYTIME RUNNING LIGHT SYSTEM : Component Function 1.CHECK TAIL LAMP OPERATION CONSULT-III ACTIVE TEST 1. Select “EXTERNAL LAMPS” of IPDM E/R active tes ...Light & rain sensor
Component Function Check 1.CHECK LIGHT & RAIN SENSOR 1. Clean light & rain sensor detection area of windshield fully. 2. Turn ignition switch ON. 3. Turn lighting switch AUTO. 4. With the ...Other materials:
Antenna base
Exploded View
1. Antenna rod
2. Antenna base
: N·m (kg-m, in-lb)
Removal and Installation
REMOVAL
1. Remove headlining. Refer to INT-26, "Exploded View".
2. Disconnect antenna feeder connector.
3. Remove nut to remove antenna base.
INSTALLATION
Install in the reverse order o ...
Transmission range switch
Exploded View
1. Transmission range switch
2. Transaxle assem
Removal and Installation
REMOVAL
1. Remove battery. Refer to PG-124, "Removal and Installation".
2. Remove transmission range switch connector.
3. Remove control cable. Refer to TM-273, "Removal and Installation&q ...
P0833 CPP switch
DTC Logic
DTC DETECTION LOGIC
Diagnosis Procedure
1.CHECK CLUTCH PEDAL POSITION SWITCH GROUND CIRCUIT FOR OPEN AND SHORT
1. Turn ignition switch OFF.
2. Disconnect clutch pedal position switch harness connector.
3. Check the continuity between clutch pedal position switch harness connector
...