Nissan Juke Service and Repair Manual : Insufficient heating
Description
Symptom
• Insufficient heating
• No warm air comes out. (Air flow volume is normal.)
Diagnosis Procedure
NOTE
:
Perform self-diagnosis with CONSULT-III before performing symptom diagnosis. If
any malfunction result or
DTC is detected, perform the corresponding diagnosis.
1.CHECK COOLING SYSTEM
1. Check engine coolant level and check for leakage. Refer to the following.
- HR16DE: Refer to CO-37, "Inspection".
- MR16DDT: Refer to CO-11, "Inspection".
- K9K: Refer to CO-62, "Inspection".
2. Check radiator cap (HR16DE and MR16DDT) or reservoir tank cap (K9K). Refer to the following.
- HR16DE: Refer to CO-40, "RADIATOR CAP : Inspection".
- MR16DDT: Refer to CO-15, "RADIATOR CAP : Inspection".
- K9K: Refer to CO-65, "Inspection".
3. Check water flow sounds of the engine coolant. Refer to the following.
- HR16DE: Refer to CO-38, "Refilling".
- MR16DDT: Refer to CO-12, "Refilling".
- K9K: Refer to CO-63, "Refilling".
Is the inspection result normal? YES-1 >> HR16DE and MR16DDT: GO TO 3.
YES-2 >> K9K: GO TO 2.
NO >> Refill engine coolant and repair or replace the parts depending on the inspection results.
2.CHECK PTC HEATER OPERATION
Check PTC heater operation. Refer to HAC-294, "Component Function Check".
Is the inspection result normal? YES >> GO TO 3.
NO >> Repair or replace parts depending on the inspection results.
3.CHECK HEATER HOSE
Check installation of heater hose by visually or touching.
Is the inspection result normal? YES >> GO TO 4.
NO >> Repair or replace parts depending on the inspection results.
4.CHECK HEATER CORE
1. Check temperature of inlet hose and outlet hose of heater core.
2. Check that inlet side of heater core is hot and the outlet side is slightly lower than/almost equal to the inlet side.
CAUTION:
Always perform the temperature inspection in a short period of time because the
engine coolant
temperature is very hot.
Is the inspection result normal?
YES >> GO TO 5.
NO-1 >> HR16DE: Replace heater core. Refer to HA-56, "HEATER CORE : Removal and Installation".
NO-2 >> MR16DDT: Replace heater core. Refer to HA-116, "HEATER CORE : Removal and Installation".
NO-3 >> K9K: Replace heater core.
5.CHECK AIR LEAKAGE FROM EACH DUCT
Check duct and nozzle, etc. of air conditioning system for air leakage.
Is the inspection result normal? YES >> Check air mix door cable installation and air mix door operation.
NO >> Repair or replace parts depending on the inspection results.
Insufficient cooling
Description Symptom • Insufficient cooling • No cool air comes out. (Air flow volume is normal.) Diagnosis Procedure NOTE: Perform self-diagnosis with CONSULT-III before performing symptom diagn ...Compressor dose dot operate
Description SYMPTOM Compressor dose not operate. Diagnosis Procedure NOTE: • Perform self-diagnosis with CONSULT-III before performing symptom diagnosis. If any malfunction result or DTC is de ...Other materials:
Front fog lamp aiming adjustment
Description
PREPARATION BEFORE ADJUSTING
NOTE:
For details, refer to the regulations in your own country.
Before performing aiming adjustment, check the following.
• Adjust the tire pressure to the specification.
• Fill with fuel, engine coolant and each oil.
• Maintain the unloaded vehic ...
BCM
Removal and Installation
CAUTION:
Before replacing BCM, perform “READ CONFIGURATION” to save or print current
vehicle specification.
Refer to BCS-80, "ADDITIONAL SERVICE WHEN REPLACING CONTROL UNIT (BCM) :
Description".
REMOVAL (RHD MODELS)
1. Remove glove box assembly. Refer to I ...
P0133 A/F sensor 1
DTC Logic
DTC DETECTION LOGIC
To judge the malfunction of A/F sensor 1, this diagnosis measures response
time of the A/F signal computed
by ECM from the A/F sensor 1 signal. The time is compensated by engine operating
(speed and load), fuel
feedback control constant, and the A/F sensor 1 tem ...