Nissan Juke Service and Repair Manual : Headlamp (LO) circuit

Component Function Check

1.CHECK HEADLAMP (LO) OPERATION

1. Select “EXTERNAL LAMPS” of IPDM E/R active test item.CONSULT-III ACTIVE TEST


1. Select “EXTERNAL LAMPS” of IPDM E/R active test item.

2. With operating the test items, check that the headlamp (LO) is turned ON.

Lo : Headlamp (LO) ON Off : Headlamp (LO) OFF

Is the inspection result normal? YES >> Headlamp (LO) is normal.

NO >> Refer to EXL-47, "Diagnosis Procedure".

Diagnosis Procedure

1.CHECK HEADLAMP (LO) OUTPUT VOLTAGE

1. Turn ignition switch OFF.CONSULT-III ACTIVE TEST


1. Turn ignition switch OFF.

2. Disconnect headlamp connector.

3. Turn ignition switch ON.

4. Select “EXTERNAL LAMPS” of IPDM E/R active test item.

5. With operating the test items, check voltage between IPDM E/R harness connector and ground.

Is the inspection result normal?


Is the inspection result normal? YES >> GO TO 2.

NO >> GO TO 3.

2.CHECK HEADLAMP (LO) OPEN CIRCUIT 1. Turn ignition switch OFF.

2. Disconnect IPDM E/R connector.

3. Check continuity between IPDM E/R harness connector and headlamp harness connector.

Is the inspection result normal?


Is the inspection result normal? YES >> Replace headlamp bulb.

NO >> Repair or replace harness.

3.CHECK HEADLAMP (LO) FUSE

1. Turn ignition switch OFF.

2. Check that the following fuses are not fusing.

Is the inspection result normal?


Is the inspection result normal? YES >> Replace IPDM E/R.

NO >> GO TO 4.

4.CHECK HEADLAMP (LO) SHORT CIRCUIT

1. Disconnect IPDM E/R connector.

2. Check continuity between IPDM E/R harness connector and ground.

Is the inspection result normal?


Is the inspection result normal? YES >> Replace the fuse. (Replace IPDM E/R if the fuse is fusing again.) NO >> Repair or replace harness. And then replace the fuse.

    Headlamp (HI) circuit
    Component Function Check 1.CHECK HEADLAMP (HI) OPERATION CONSULT-III ACTIVE TEST 1. Select “EXTERNAL LAMPS” of IPDM E/R active test item. 2. With operating the test items, check that the headlamp ...

    Headlamp ground circuit
    Diagnosis Procedure 1.CHECK HEADLAMP GROUND OPEN CIRCUIT 1. Turn ignition switch OFF. 2. Disconnect headlamp connector. 3. Check continuity between headlamp harness connector and ground. Is the ...

    Other materials:

    Removal and Installation
    REMOVAL • Disconnect each joint and mounting. • Remove heated oxygen sensor 2 with following procedure: - Using heated oxygen sensor wrench [SST: KV10114400] (A), removal heated oxygen sensor 2 (1). CAUTION: Be careful not to damage heated oxygen sensor 2. INSTALLATION Note the following ...

    P0201, P0202, P0203, P0204 fuel injector
    DTC Logic DTC DETECTION LOGIC NOTE: If DTC P0201, P0202, P0203 or P0204 is displayed with DTC P0263, P0266, P0269 or P0272 first perform trouble diagnosis for DTC P0263, P0266, P0269 or P0272. Refer to EC-931, "DTC Logic". Diagnosis Procedure 1.CHECK FUEL INJECTOR POWER SUPPLY ...

    P2135 TP sensor
    DTC Logic DTC DETECTION LOGIC NOTE: If DTC P2135 is displayed with DTC P0643, first perform the trouble diagnosis for DTC P0643. Refer to EC-686, "DTC Logic". DTC CONFIRMATION PROCEDURE 1.PRECONDITIONING If DTC Confirmation Procedure has been previously conducted, always turn ...