Nissan Juke Service and Repair Manual : Fuel pressure

Work Procedure

FUEL PRESSURE RELEASE

1. Turn ignition switch ON. With CONSULT-III


1. Turn ignition switch ON.

2. Perform “FUEL PRESSURE RELEASE” in “WORK SUPPORT” mode of “ENGINE” using CONSULT-III.

3. Start engine.

4. After engine stalls, crank it two or three times to release all fuel pressure.

5. Turn ignition switch OFF.

1. Remove fuel pump fuse located in IPDM E/R. Without CONSULT-III


1. Remove fuel pump fuse located in IPDM E/R.

2. Start engine.

3. After engine stalls, crank it two or three times to release all fuel pressure.

4. Turn ignition switch OFF.

5. Reinstall fuel pump fuse after servicing fuel system.

FUEL PRESSURE CHECK

CAUTION:
• Before disconnecting fuel line, release fuel pressure from fuel line to eliminate danger.

• The fuel hose connection method used when taking fuel pressure check must not be used for other purposes.

• Be careful not to scratch or put debris around connection area when servicing, so that the quick connector maintains sealability with O-rings inside.

• Do not perform fuel pressure check with electrical systems operating (i.e. lights, rear defogger, A/C, etc.) Fuel pressure gauge may indicate false readings due to varying engine load and changes in manifold vacuum.

NOTE:

Prepare pans or saucers under the disconnected fuel line because the fuel may spill out. The fuel pressure cannot be completely released because J10 models do not have fuel return system.

1. Release fuel pressure to zero.

2. Prepare fuel hose for fuel pressure check B and fuel tube adapter [SST: KV10118400] D, then connect fuel pressure gauge A.

• : To fuel tube (engine side) : To quick connector
• C: Clamp: To fuel tube (engine side)
• C: Clamp
• Use suitable fuel hose for fuel pressure check (genuine NISSAN fuel hose without quick connector).

• To avoid unnecessary force or tension to hose, use moderately long fuel hose for fuel pressure check.

• Do not use the fuel hose for checking fuel pressure with damage or cracks on it.

• Use Pressure Gauge to check fuel pressure.

3. Remove fuel hose.

• Do not twist or kink fuel hose because it is plastic hose.

4. Connect fuel hose for fuel pressure check (1) to fuel tube


4. Connect fuel hose for fuel pressure check (1) to fuel tube (engine side) with clamp (2) as shown in the figure.

• No.2 spool (5)
• Wipe off oil or dirt from hose insertion part using cloth moistened with gasoline.

• Apply proper amount of gasoline between top of the fuel tube (3) and No.1 spool (4).

• Insert fuel hose for fuel pressure check until it touches the No.1 spool on fuel tube.

• Use NISSAN genuine hose clamp (part number: 16439 N4710 or 16439 40U00).

• When reconnecting fuel line, always use new clamps.

• Use a torque driver to tighten clamps.

• Install hose clamp to the position within 1 - 2 mm (0.04 - 0.08 in).

Tightening torque: 1 - 1.5 N·m (0.1 - 0.15 kg-m, 9 - 13 in-lb)


Tightening torque: 1 - 1.5 N·m (0.1 - 0.15 kg-m, 9 - 13 in-lb)

• Make sure that clamp screw does not contact adjacent parts.

5. Connect fuel tube adapter to quick connector.

• A: Fuel pressure gauge • B: Fuel hose for fuel pressure check 6. After connecting fuel hose for fuel pressure check, pull the hose with a force of approximately 98 N (10 kg, 22 lb) to confirm fuel tube does not come off.

7. Turn ignition switch ON and check for fuel leakage.

8. Start engine and check for fuel leakage.

9. Read the indication of fuel pressure gauge.

• Do not perform fuel pressure check with system operating.

Fuel pressure gauge may indicate false readings.

• During fuel pressure check, confirm for fuel leakage from fuel connection every 3 minutes.

At idling: Approximately 350 kPa (3.5 bar, 3.57 kg/cm2, 51 psi)


At idling: Approximately 350 kPa (3.5 bar, 3.57 kg/cm2, 51 psi)

10. If result is unsatisfactory, go to next step.

11. Check the following.

• Fuel hoses and fuel tubes for clogging • Fuel filter for clogging • Fuel pump
• Fuel pressure regulator for clogging

If OK, replace fuel pressure regulator.

If NG, repair or replace.

    Mixture ratio self-learning value clear
    Description This describes how to erase the mixture ratio self-learning value. For the actual procedure, follow the instructions in “Diagnosis Procedure”. Work Procedure With CONSULT-III 1. Sta ...

    How to set srt code
    Description OUTLINE In order to set all SRTs, the self-diagnoses as in the “SRT ITEM” table must have been performed at least once. Each diagnosis may require actual driving for a long period of ...

    Other materials:

    Diagnosis system (BCM) (without intelligent key system)
    Description Air conditioning system performs self-diagnosis, operation check, function diagnosis, and various settings using diagnosis function of each control unit. Common item : consult-III Function (BCM - COMMON ITEM) APPLICATION ITEM CONSULT-III performs the following functions via CAN ...

    P0340 CMP sensor (phase)
    DTC Logic DTC DETECTION LOGIC Diagnosis Procedure 1.CHECK GROUND CONNECTIONS 1. Turn ignition switch OFF. 2. Check ground connection E38. Refer to Ground inspection in GI-44, "Circuit Inspection". Is the inspection result normal? YES >> GO TO 2. NO >> Repair or ...

    Assembly and Installation
    • Use torque wrench to tighten bolts or nuts to specification. • When tightening nuts and bolts, as a basic rule, equally tighten in several different steps starting with the ones in center, then ones on inside and outside diagonally in this order. If the order of tightening is specified, do ...