Nissan Juke Service and Repair Manual : Fuel filler lid opener

Exploded View

1. Fuel filler lid opener cable


1. Fuel filler lid opener cable 2. Cable protector
3. Fuel filler lid lock assembly 4. Fuel filler lid assembly 5. Spring
6. Bumper rubber

: Do not reuse: Clip
Fuel filler lid: Do not reuse


Fuel filler lid

FUEL FILLER LID : Removal and Installation

REMOVAL

1. Fully open fuel filler lid.

2. Remove fuel mounting pin (1).

3. Remove mounting screws, and then remove fuel filler lid.


3. Remove mounting screws, and then remove fuel filler lid.

INSTALLATION

Note the following items, and install in the reverse order of removal.

CAUTION:
• After installation, check fuel filler lid assembly open/close, lock/unlock operation.

• After installation, apply the touch-up paint (the body color) onto the head of the mounting screws.

NOTE:

• The following table shows the specifide values for checking nomal installation status.

• Fitting adjustment cannot be perfomed.

Fuel filler opener cable


Fuel filler opener cable

FUEL FILLER OPENER CABLE : Removal and Installation

REMOVAL

1. Remove hood lock control cable assembly from instrument lower panel (LH). Refer to DLK-587, "HOOD LOCK CONTROL CABLE : Removal and Installation".

2. Remove fuel filler lid opener cable (2) from fuel filler lid opener lever (1).

3. Remove front kicking plate inner (LH) and rear kicking plate inner (LH and


3. Remove front kicking plate inner (LH) and rear kicking plate inner (LH and RH). Refer to INT-19, "KICKING PLATE INNER : Removal and Installation".

4. Remove dash side finisher (LH). Refer to INT-20, "DASH SIDE FINISHER : Removal and Installation".

5. Remove center pillar lower garnish (LH). Refer to INT-20, "CENTER PILLAR LOWER GARNISH : Removal and Installation".

6. Remove luggage side lower finisher (RH). Refer to INT-31, "LUGGAGE SIDE LOWER FINISHER : Removal and Installation".

7. Remove fuel filler lid opener cable from fuel filler lid lock assembly. Refer to DLK-600, "FUEL FILLER LID LOCK : Removal and Installation".

8. Disengage each harness protector (1), and then remove fuel filler lid opener cable (2).

9. Remove fuel filler lid opener cable fixing clips, and then remove fuel


9. Remove fuel filler lid opener cable fixing clips, and then remove fuel filler lid opener cable.

INSTALLATION

Note the following item, and install in the reverse order of removal.

CAUTION:
After installation, check fuel filler lid assembly open/close, lock/unlock operation.

FUEL FILLER LID LOCK

FUEL FILLER LID LOCK : Removal and Installation

REMOVAL

1. Fully open fuel filler lid.

2. Remove luggage side lower finisher (RH). Refer to INT-31, "LUGGAGE SIDE LOWER FINISHER : Removal and Installation".

3. Rotate and disengage fuel filler lid lock assembly, and then remove fuel filler lid lock assembly.

NOTE

:
Operation is performed easily when rotating fuel filler lid lock from passenger room side.

4. Disengage fuel filler lid opener cable (1). Remove fuel filler lid


4. Disengage fuel filler lid opener cable (1). Remove fuel filler lid opener cable while pressing stopper pin (2).

INSTALLATION


INSTALLATION

Note the following item, and install in the reverse order of removal.

CAUTION:
After installation, check fuel filler lid assembly open/close, lock/unlock operation.

    Back door lock
    Exploded View 1. Back door lock assembly 2. TORX bolt 3. Back door striker : Do not reuse : N·m (kg-m, ft-lb) : Body grease Door lock DOOR LOCK : Removal and Installation REMOVAL 1. Remo ...

    Door switch
    Exploded View 1. Door switch 2. TORX bolt Removal and Installation REMOVAL Remove the TORX bolt (A), and then remove door switch (1). INSTALLATION Install in the reverse order of removal. ...

    Other materials:

    Diagnosis systeM (BCM) (without intelligent key system)
    Common item COMMON ITEM : CONSULT-III Function (BCM - COMMON ITEM) APPLICATION ITEM CONSULT-III performs the following functions via CAN communication with BCM. SYSTEM APPLICATION BCM can perform the following functions for each system. NOTE: It can perform the diagnosis modes except the ...

    P17BB primary pressure solenoid
    DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.PREPARATION BEFORE WORK If another "DTC CONFIRMATION PROCEDURE" occurs just before, turn ignition switch OFF and wait for at least 10 seconds, then perform the next test. >> GO TO 2. 2.CHECK DTC DETECTION 1. S ...

    Glass
    Use glass cleaner to remove smoke and dust film from the glass surfaces. It is normal for glass to become coated with a film after the vehicle is parked in the hot sun. Glass cleaner and a soft cloth will easily remove this film. CAUTION When cleaning the inside of the windows, do not use shar ...