Nissan Juke Owners Manual : Fuel-filler cap
To remove the fuel-filler cap:
1. Turn the fuel-filler cap counterclockwise 1 to remove.
2. Put the fuel-filler cap on the cap holder A while refueling.
To install the fuel-filler cap:
1. Insert the fuel-filler cap straight into the fuelfiller tube.
2. Turn the fuel-filler cap clockwise 2 until a single click is heard.
WARNING
• Gasoline is extremely flammable and highly explosive under certain conditions. You could be burned or seriously injured if it is misused or mishandled. Always stop engine and do not smoke or allow open flames or sparks near the vehicle when refueling.
• Do not attempt to top off the fuel tank after the fuel pump nozzle shuts off automatically. Continued refueling may cause fuel overflow, resulting in fuel spray and possibly a fire.
• Use only an original equipment type fuel-filler cap as a replacement. It has a built-in safety valve needed for proper operation of the fuel system and emission control system.
An incorrect cap can result in a serious malfunction and possible injury. It could also cause the malfunction indicator light to come on.
• Never pour fuel into the throttle body to attempt to start your vehicle.
• Do not fill a portable fuel container in the vehicle or trailer. Static electricity can cause an explosion of flammable liquid, vapor or gas in any vehicle or trailer. To reduce the risk of serious injury or death when filling portable fuel containers: — Always place the container on the ground when filling.
— Do not use electronic devices when filling.
— Keep the pump nozzle in contact with the container while you are filling it.
— Use only approved portable fuel containers for flammable liquid.
CAUTION
• If fuel is spilled on the vehicle body, flush it away with water to avoid paint damage.
• Insert the cap straight into the fuelfiller tube, then tighten until the
fuel-filler cap clicks. Failure to tighten the fuel-filler cap properly may cause
the malfunction indicator light (MIL)
to illuminate. If the light illuminates
because the fuelfiller cap is loose or missing, tighten or install the cap and continue
to drive the vehicle. The light should
turn off after a few driving trips. If the
light does not turn off after a few
driving trips, have the vehicle inspected by a NISSAN dealer.
For additional information, see “Malfunction Indicator Light (MIL)” .
• The LOOSE FUEL CAP warning message will be displayed if the fuel-filler cap is not properly tightened.
It may take a few driving trips for the message to be displayed.
Failure to tighten the fuel-filler cap properly after the LOOSE FUEL CAP warning
message is displayed may cause the
Malfunction Indicator Light (MIL) to illuminate.
LOOSE FUEL CAP warning message
The LOOSE FUEL CAP warning message is displayed on the vehicle information display when the fuel-filler cap is not tightened correctly after the vehicle has been refueled. It may take a few driving trips for the message to be displayed. To turn off the warning message, do the following procedure:
1. Remove and install the fuel-filler cap as previously described as soon as possible.
2. Tighten the fuel-filler cap until it clicks.
3. Push the trip computer mode switchA for about 1 second to turn off the LOOSE FUEL CAP warning message after tightening the fuel cap.
Opening the fuel-filler door
To open the fuel-filler door, pull the release handle located below the instrument panel. To lock, close the fuel-filler door securely. ...Tilt steering column
WARNING Do not adjust the steering wheel while driving. You could lose control of your vehicle and cause an accident. ...Other materials:
P0606 ECM
DTC Logic
DTC DETECTION LOGIC
Diagnosis Procedure
1.INSPECTION START
1. Turn ignition switch ON.
2. Erase DTC.
3. Turn ignition switch OFF and wait for 20 seconds.
4. Turn ignition switch ON and perform the self-diagnosis.
Is the DTC P0606 displayed again?
YES >> GO TO 2.
NO &g ...
Door cable
Exploded View
LEFT SIDE
1. A/C unit assembly
2. Intake door lever
3. Intake door link
4. Intake door cable
5. Air mix door cable
6. Air mix door link
7. Air mix door rod
8. Lower air mix door lever
9. Upper air mix door lever
10. Max. cool door
A. To A/C control
RIGHT SIDE
...
System
POWER DISTRIBUTION SYSTEM
POWER DISTRIBUTION SYSTEM : System Description
SYSTEM DESCRIPTION
• PDS (POWER DISTRIBUTION SYSTEM) is the system that BCM controls with the
operation of the pushbutton
ignition switch and performs the power distribution to each power circuit. This
system is used in ...