Nissan Juke Service and Repair Manual : Front wiper drive assembly
Exploded View
REMOVAL
LHD models
1. Front wiper arm cap
2. Front wiper arm LH
3. Front wiper blade LH
4. Front wiper arm RH
5. Front wiper blade RH
6. Front wiper drive assembly
: Pawl
: N·m (kg-m, in-lb)
: N·m (kg-m, ft-lb)
RHD models
1. Front wiper arm cap
2. Front wiper arm RH
3. Front wiper drive assembly
4. Front wiper motor
5. Front wiper blade LH
6. Front wiper arm LH
7. Front wiper blade RH
: Pawl
: N·m (kg-m, in-lb)
: N·m (kg-m, ft-lb)
DISASSEMBLY
LHD models
1. Front wiper linkage 1
2. Shaft seal
3. Front wiper frame
4. Front wiper motor
5. Front wiper linkage 2
6. Front wiper arm LH
: Nissan MP special grease No
RHD models
1. Front wiper linkage 1
2. Shaft seal
3. Front wiper frame
4. Front wiper motor
5. Front wiper linkage 2
6. Front wiper arm LH
: Nissan MP special grease No.2
Removal and Installation
REMOVAL
1. Remove front wiper arms (LH and RH). Refer to WW-76, "Removal and Installation".
2. Remove cowl top cover. Refer to EXT-20, "Removal and Installation".
3. Disconnect the front wiper motor connector.
4. Remove the mounting bolts from front wiper drive assembly.
5. Remove the front wiper drive assembly from the vehicle.
INSTALLATION
1. Install the front wiper drive assembly to the vehicle.
2. Connect front wiper motor connector.
3. Operate front wiper to move it to the auto stop position.
4. Install cowl top cover. Refer to EXT-20, "Removal and Installation".
5. Install front wiper arms. Refer to WW-76, "Removal and Installation".
Disassembly and Assembly
DISASSEMBLY
1. Remove the front wiper linkage 1 and 2 from the front wiper drive assembly.
CAUTION:
Never bend the linkage or damage the plastic part of the ball joint when
removing the wiper linkage.
2. Remove the front wiper motor mounting screws, and then remove the front wiper motor from the front wiper frame.
ASSEMBLY
1. Connect the front wiper motor connector.
2. Operate the front wiper to move it to the auto stop position.
3. Disconnect the front wiper motor connector.
4. Install the front wiper motor to the front wiper frame.
5. Install the front wiper linkage 2 to the front wiper motor and the front wiper frame.
6. Install the front wiper linkage 1 to the front wiper frame.
CAUTION:
• Never drop front wiper motor or cause it to come into contact with other
parts.
• Be careful for the grease condition at the front wiper motor and front wiper linkage joint (retainer). Apply Multi−purpose grease or an equivalent if necessary.
Front wiper blade
Exploded View 1. Wiper blade 2. Wiper arm Removal and Installation REMOVAL Push up the lever (A) of wiper blade (1), while sliding wiper blade toward the direction of the arrow to remove it f ...Light & rain sensor
Exploded View 1. Light & rain sensor bracket 2. Mirror base 3. Light & rain sensor 4. Inside mirror assembly : Pawl : Do not reuse Removal and Installation CAUTION: When the light ...Other materials:
Power supply and ground circuit
A/C auto AMP. : Diagnosis Procedure
1.CHECK SYMPTOM
Check symptom (A or B).
Which symptom is detected?
A >>GO TO 2.
B >>GO TO 5.
2.CHECK FUSE
1. Turn ignition switch OFF.
2. Check 10A fuse (No. 3, located in fuse block (J/B)].
NOTE:
Refer to PG-22, "Fuse, Connector ...
P173B 1GR incorrect ratio
DTC Logic
DTC CONFIRMATION PROCEDURE
CAUTION:
• Be sure to perform “TM-445, "Diagnosis Procedure"” and then perform “DTC
CONFIRMATION PROCEDURE”.
• Never perform "DTC CONFIRMATION PROCEDURE" before the repairs. Doing so may
result in a secondary
malfunction.
• Be carefu ...
Evap canister
2WD : Hydraulic Layout
EVAPORATIVE EMISSION LINE DRAWING
1.EVAP canister purge volume control
solenoid valve
2. EVAP canister
3. EAVP line
4. Fuel line
NOTE:
Do not use soapy water or any type of solvent while installing vacuum hose or
purge hoses.
2WD : Removal and Installation
REMOV ...