Nissan Juke Service and Repair Manual : Front fog lamp circuit

Component Function Check

1.CHECK FRONT FOG LAMP OPERATION

1. Select “EXTERNAL LAMPS” of IPDM E/R active test item.CONSULT-III ACTIVE TEST


1. Select “EXTERNAL LAMPS” of IPDM E/R active test item.

2. With operating the test items, check that the front fog lamp is turned ON.

Fog : Front fog lamp ON Off : Front fog lamp OFF

Is the measurement normal? YES >> Front fog lamp circuit is normal.

NO >> Refer to EXL-54, "Diagnosis Procedure".

Diagnosis Procedure

1

.CHECK FRONT FOG LAMP FUSE

1. Turn ignition switch OFF.

2. Check that the following fuse is not fusing.

Is the inspection result normal?


Is the inspection result normal? YES >> GO TO 3.

NO >> GO TO 2.

2.CHECK FRONT FOG LAMP SHORT CIRCUIT

1. Disconnect front fog connector and IPDM E/R connector.

2. Check continuity between IPDM E/R harness connector and ground.

Is the inspection result normal?


Is the inspection result normal? YES >> Replace fuse. (Replace IPDM E/R if the fuse is fusing again.) NO >> Repair or replace harness. And then replace the fuse.

3.CHECK FRONT FOG LAMP BULB

Check the applicable lamp bulb.

Is the inspection result normal? YES >> GO TO 4.

NO >> Replace bulb.

4.CHECK FRONT FOG LAMP OUTPUT VOLTAGE

1. Disconnect front fog lamp connector.CONSULT-III ACTIVE TEST


1. Disconnect front fog lamp connector.

2. Turn ignition switch ON.

3. Select “EXTERNAL LAMPS” of IPDM E/R active test item.

4. With operating the test items, check the voltage between IPDM E/R harness connector and ground.

Is the inspection result normal?


Is the inspection result normal? YES >> GO TO 5.

NO >> Replace IPDM E/R.

5.CHECK FRONT FOG LAMP OPEN CIRCUIT

1. Turn ignition switch OFF.

2. Disconnect IPDM E/R connector.

3. Check continuity between IPDM E/R harness connector and front fog lamp harness connector.

Is the inspection result normal?


Is the inspection result normal? YES >> GO TO 6.

NO >> Repair or replace harness.

6.CHECK FRONT FOG LAMP GROUND CIRCUIT OPEN CIRCUIT

Check continuity between front fog lamp harness connector and grou

Is the inspection result normal?


Is the inspection result normal? YES >> Refer to GI-42, "Intermittent Incident".

NO >> Repair or replace harness.

    Headlamp aiming system (manual)
    Component Inspection 1.CHECK HEADLAMP AIMING SWITCH 1. Remove headlamp aiming switch. 2. Check resistance among each headlamp aiming switch terminal. Is the inspection result normal? YES >&g ...

    Rear fog lamp circuit
    Component Function Check 1.CHECK REAR FOG LAMP OPERATION CONSULT-III ACTIVE TEST 1. Select “RR FOG LAMP” of BCM (HEAD LAMP) active test item. 2. With operating the test items, check that the rear ...

    Other materials:

    Side oil seal
    Removal and Installation REMOVAL 1. Remove front drive shafts. Refer to FAX-53, "Removal and Installation". 2. Remove differential side oil seals (1) from clutch housing and transaxle case, using an oil seal remover. CAUTION: Never damage transaxle case and clutch housing. INSTA ...

    Basic inspection
    DIAGNOSIS AND REPAIR WORK FLOW Work Flow DETAILED FLOW 1.OBTAIN INFORMATION ABOUT SYMPTOM Interview the customer to obtain as much malfunction information (conditions and environment when the malfunction occurred) as possible when the customer brings the vehicle in. >> GO TO 2. 2. ...

    Too much power
    Description CHART 13: TOO MUCH POWER Diagnosis Procedure 1.CHECK ECM POWER SUPPLY AND GROUND CIRCUIT Check ECM power supply and ground circuit. Refer to EC-885, "Diagnosis Procedure". Is the inspection result normal? YES >> GO TO 2. NO >> Repair or replace harness ...