Nissan Juke Service and Repair Manual : Front bumper

Exploded View

1. Front side grille RH


1. Front side grille RH 2. Front side grille LH 3. Bumper side bracket RH 4. Front center grille
5. Emblem
6. Bumper reinforcement
7. Energy absorber
8. Bumper end rubber RH 9. Bumper fascia
10. Screw grommet
11. Bumper bracket cover 12. License plate bracket 13. Front fog bracket RH 14. Bumper fascia lower 15. U nut
16. Front fog bracket LH 17. Bumper end rubber LH 18. Bumper side bracket LH 19. Screw grommet
20. double-sided tape
[t: 1.2 mm (0.047 in)]

: Do not reuse: Pawl
Removal and Installation: Do not reuse


Removal and Installation

CAUTION:
Bumper fascia is made of resin. Never apply strong force to it, and be careful to prevent contact with oil.

REMOVAL

1. Fully open hood assembly.

2. Remove clips (A) of bumper upper side.

3. Remove front fillet molding front side. Refer toEXT-26, "FRONT FILLET


3. Remove front fillet molding front side. Refer toEXT-26, "FRONT FILLET MOLDING : Removal and Installation".

4. Remove bumper fascia assembly fixing screws (A) (LH and RH).

5. Remove air guide fixing screws, and then remove air guide (LH and


5. Remove air guide fixing screws, and then remove air guide (LH and RH).Refer to EXT-22, "Exploded View".

6. Remove clips of bumper lower side.

7. Pull bumper fascia side toward the vehicle side to disengage the fitting of bumper side bracket and bumper fascia side as shown by the arrow in the figure.

8. CAUTION:: Pawl


8. CAUTION:
When removing bumper fascia assembly, 2 workers are required so as to prevent it from dropping.

9. Disconnect front fog lamp harness connectors. (with fog lamp)


9. Disconnect front fog lamp harness connectors. (with fog lamp) 10. Remove bumper fascia assembly.

11. Remove the following parts after removing bumper fascia assembly.

• Front fog lamp assembly (LH and RH). (with fog lamp) • Front fog lamp finishers (LH and RH). (with out fog lamp) • Bumper fascia lower
• License plate bracket

12. Remove bumper energy absorber.

13. Remove bumper reinforcement mounting nuts, and then remove bumper reinforcement.

14. Remove bumper side bracket mounting screws, and then remove bumper side bracket.

INSTALLATION

Note the following items, and then install in the reverse order of removal.

NOTE

:
• The following table shows the specified values for checking normal installation status.

• Fitting adjustment cannot be performed.


Rear bumper


    Rear bumper
    Exploded View 1. Bumper side bracket LH 2. Bumper closing LH 3. Bumper fascia assembly 4. Reflex reflector LH 5. Rear panel lower 6. U nut 7. Bumper fascia lower 8. Reflex reflector RH ...

    Other materials:

    P0444 EVAP canister purge volume control solenoid valve
    DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.CONDITIONING If DTC Confirmation Procedure has been previously conducted, always turn ignition switch OFF and wait at least 10 seconds before conducting the next test. TESTING CONDITION: Before performing the following procedure ...

    Terms
    • The captions WARNING and CAUTION warn you of steps that must be followed to prevent personal injury and/or damage to some part of the vehicle. WARNING indicates the possibility of personal injury if instructions are not followed. CAUTION indicates the possibility of component damage if ...

    Combination meter
    Reference Value VALUES ON THE DIAGNOSIS TOOL NOTE: Some items are not available according to vehicle specification. TERMINAL LAYOUT PHYSICAL VALUES Fail-Safe FAIL-SAFE The combination meter activates the fail-safe control if CAN communication with each unit is malfuncti ...