Nissan Juke Service and Repair Manual : Fluid cooler system

Exploded View

1. Copper washer


1. Copper washer
2. CVT fluid cooler tube 3. Hose clamp
4. Fluid cooler hose A
5. Fluid cooler tube
6. Fluid cooler hose B
7. Fluid cooler hose C
8. Transaxle assembly
9. Fluid cooler hose D
10. Fluid cooler hose E 11. Fluid cooler hose F 12. Bypass valve
13. Fluid cooler
14. Air guide
15. Bracket A
16. Bracket B

A. To radiator

Removal and Installation: Vehicle side


Removal and Installation

REMOVAL

1. Remove engine under cover.

2. Remove front bumper assembly. Refer to EXT-13, "Removal and Installation".

3. Remove air guide from fluid cooler.

4. Remove fluid cooler hose E and fluid cooler hose F.

5. Remove fluid cooler.

6. Remove air duct (inlet). Refer to EM-26, "Removal and Installation".

7. Remove fluid cooler hose C and fluid cooler hose D.

8. Remove bypass valve from bracket B.

9. Remove fluid cooler hose A and fluid cooler hose B.

10. Remove fluid cooler tube.

11. Remove bracket A and bracket B.

12. Remove CVT fluid cooler tube from transaxle assembly.

INSTALLATION

Note the following, and install in the reverse order of removal.

CAUTION:
Never reuse copper washer.

• When installing CVT fluid cooler tube (1) to transaxle assembly: - Contact CVT fluid cooler tube a boss portion (A) of the transaxle case.

- Tighten the bolt of CVT fluid cooler tube without moving the CVT fluid cooler tube

• Refer to the followings when installing fluid cooler hose.


• Refer to the followings when installing fluid cooler hose.


*: Refer to the illustrations for the specific position each hose clamp tab.


*: Refer to the illustrations for the specific position each hose clamp tab.

- The illustrations indicate the view from the hose ends.

G : Vehicle frontF : Vehicle upper
- When installing hose clamps center line of each hose clamp tabG : Vehicle front


- When installing hose clamps center line of each hose clamp tab should be positioned as shown in the figure.

- Insert fluid cooler hose according to dimension (L) described below.


- Insert fluid cooler hose according to dimension (L) described below.


- Set hose clamps (1) at the both ends of fluid cooler hose (2) with


- Set hose clamps (1) at the both ends of fluid cooler hose (2) with dimension (A) from the hose edge.

- Hose clamp should not interfere with the bulge of fluid cooler tube.


- Hose clamp should not interfere with the bulge of fluid cooler tube.

Inspection


Inspection

INSPECTION AFTER INSTALLATION

Check for CVT fluid leakage and CVT fluid level. Refer to TM-184, "Inspection".

    Water hose
    Exploded View 1. Hose clamp 2. Water hose A. Water outlet B. Oil warm Removal and Installation REMOVAL WARNING: Never remove the radiator cap when the engine is hot. Serious burns could oc ...

    Unit removal and installation
    Transaxle assembly Exploded View 1. CVT fluid level gauge 2. CVT fluid charging pipe 3. O-ring 4. Transaxle assembly 5. Air breather hose A. For tightening torque, refer to TM-301, "R ...

    Other materials:

    Door lock status indicator does not illuminate
    Diagnosis Procedure 1.CHECK DOOR LOCK STATUS INDICATOR Check door lock status indicator. Refer to DLK-395, "Component Function Check". Is the inspection result normal? YES >> GO TO 2. NO >> Repair or replace the malfunctioning parts. 2.CONFIRM THE OPERATION Conf ...

    Diagnosis system (BCM) (with intelligent key system)
    Common item COMMON ITEM : CONSULT-III Function (BCM - COMMON ITEM) APPLICATION ITEM CONSULT-III performs the following functions via CAN communication with BCM. SYSTEM APPLICATION BCM can perform the following functions for each system. NOTE: It can perform the diagnosis modes except the ...

    Rear wiper arm
    Exploded View 1. Rear wiper motor 2. Rear wiper blade 3. Rear wiper arm 4. Rear wiper arm cover 5. Rear wiper pivot seal A : Model for cold areas : Pawl : N·m (kg-m, in-lb) : N·m (kg-m, ft-lb) Removal and Installation REMOVAL 1. Operate rear wiper to the auto stop position. 2. Remo ...