Nissan Juke Service and Repair Manual : ESP off switch
Component Function Check
1.CHECK ESP OFF SWITCH OPERATION
Check that ESP OFF indicator lamp in combination meter turns ON/OFF when ESP OFF switch is operated.
Is the inspection result normal? YES >> INSPECTION END
NO >> Proceed to diagnosis procedure. Refer to BRC-210, "Diagnosis Procedure".
Diagnosis Procedure
1.CHECK ESP OFF SWITCH CIRCUIT
1. Turn the ignition switch OFF.
2. Disconnect ABS actuator and electric unit (control unit) harness connector.
3. Disconnect ESP OFF switch harness connector.
4. Check continuity between ABS actuator and electric unit (control unit) harness connector and ESP OFF switch harness connector.
5. Check continuity between ABS actuator and electric unit (control unit) harness connector and ground.
Is the inspection result normal? YES >> GO TO 2.
NO >> Repair or replace error-detected parts.
2.CHECK ESP OFF SWITCH GROUND CIRCUIT
Check continuity between ESP OFF switch harness connector and ground.
Is the inspection result normal? YES >> GO TO 3.
NO >> Repair or replace error-detected parts.
3.CHECK ESP OFF SWITCH
Check ESP OFF switch. Refer to BRC-211, "Component Inspection".
Is the inspection result normal? YES >> GO TO 4.
NO >> Replace ESP OFF switch. Refer to BRC-237, "Removal and Installation".
4.CHECK ESP OFF SWITCH SIGNAL
With CONSULT-III.
1. Connect ABS actuator and electric unit (control unit) harness connector.
2. Connect ESP OFF switch harness connector.
3. Select “ABS”, “DATA MONITOR” and “OFF SW” according to this order. Check ESP OFF switch signal.
Is the inspection result normal? YES >> INSPECTION END
NO >> GO TO 5.
5.CHECK TERMINAL
• Check ABS actuator and electric unit (control unit) pin terminals for damage or loose connection with harness connector.
• Check ESP OFF switch pin terminals for damage or loose connection with harness connector.
Is the inspection result normal? YES >> Replace ABS actuator and electric unit (control unit). Refer to BRC-233, "Removal and Installation".
NO >> Repair or replace error-detected parts.
Component Inspection
1.CHECK ESP OFF SWITCH
1. Turn the ignition switch OFF.
2. Disconnect triple switch harness connector.
3. Check continuity between terminals of ESP OFF switch connector.
Is the inspection result normal? YES >> INSPECTION END
NO >> Replace ESP OFF switch. Refer to BRC-237, "Removal and Installation".
Parking brake switch
Component Function Check 1.CHECK PARKING BRAKE SWITCH OPERATION Operate the parking brake lever. Then check that the brake warning lamp in the combination meter turns ON/ OFF correctly. Is the ...ABS warning lamp
Component Function Check 1.CHECK ABS WARNING LAMP FUNCTION Check that ABS warning lamp in combination meter turns ON for approx. 1 second after ignition switch is turned ON. CAUTION: Never st ...Other materials:
Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT
PRE-TENSIONER"
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”,
used along
with a front seat belt, helps to reduce the risk or severity of injury to the
driver and front passenger for certain
types of collision. Information necessary to service the system safely is
include ...
P17Ba primary pressure solenoid
DTC Logic
DTC DETECTION LOGIC
DTC CONFIRMATION PROCEDURE
1.PREPARATION BEFORE WORK
If another "DTC CONFIRMATION PROCEDURE" occurs just before, turn ignition
switch OFF and wait for at
least 10 seconds, then perform the next test.
>> GO TO 2.
2.CHECK DTC DETECTION
1. S ...
Control cable
Exploded View
1. Control cable
2. Lock plate
3. Transaxle assembly
4. Bracket A
5. Bracket B
6. CVT shift selector assembly
A: Manual lever
B: Grommet
: N·m (kg-m, ft-lb)
: N·m (kg-m, in-lb)
Removal and Installation
INSTALLATION
CAUTION:
Always apply the parking brake before per ...