Nissan Juke Service and Repair Manual : Engine stand setting

Setting

NOTE

:
Explained here is how to disassemble with engine stand supporting transaxle surface. When using different type of engine stand, note with difference in steps and etc.

1. Remove the engine and the transaxle assembly from the vehicle, and separate the transaxle from the engine.

2. Install engine to engine stand with the following procedure: a. Remove flywheel (M/T models) or drive plate (CVT models).

• Secure flywheel (M/T models) or drive plate (CVT models) (1) with a stopper plate [SST: KV11105210 (J-44716)] (A), and remove mounting bolts.

CAUTION:
• Never disassemble them.

• Never place them with signal plate facing down.

• When handling signal plate, take care not to damage or scratch them.

• Handle signal plate in a manner that prevents them from becoming magnetized.

NOTE

:
This figure shows CVT models as an example.

b. Remove pilot converter (1) using pilot bushing puller [SST:


b. Remove pilot converter (1) using pilot bushing puller [SST: ST16610001 (J-23907)] (A) or suitable tool. (CVT models) NOTE

:
M/T models have no pilot bushing.

c. Lift the engine with a hoist to install it onto widely use engine stand.


c. Lift the engine with a hoist to install it onto widely use engine stand.

CAUTION:
• Use the engine stand that has a load capacity [approximately 135 kg (298 lb) or more] large enough for supporting the engine weight.

• If the load capacity of stand is not adequate, remove the following parts beforehand to reduce the potential risk of overturning stand.

- Intake manifold: Refer to EM-28, "Exploded View".

- catalyst convertor: Refer to EM-33, "2WD : Exploded View" (2WD models) or EM-34, "4WD : Exploded View" (4WD models).

- Rocker cover: Refer to EM-53, "Exploded View".

NOTE:

The figure shows an example of widely used engine stand (A) that can support mating surface of transaxle with flywheel (M/T models) or drive plate (CVT models) removed.

CAUTION:
Before removing the hanging chains, check the engine stand is stable and there is no risk of overturning.

3. Drain engine oil. Refer to LU-9, "Draining".


3. Drain engine oil. Refer to LU-9, "Draining".

CAUTION:
Be sure to clean drain plug and install with new drain plug washer.

4. Drain engine coolant by removing water drain plug (1) from inside of the engine.

Tightening torque : Refer to EM-104, "Disassembly: Engine front


Tightening torque : Refer to EM-104, "Disassembly and Assembly".

Use Genuine Liquid Gasket or equivalent.

Engine unit


    Engine unit
    Disassembly 1. Remove intake manifold. Refer to EM-28, "Exploded View". 2. Remove catalyst convertor. Refer to EM-33, "2WD : Exploded View" (2WD models) or EM-34, "4WD : ...

    Other materials:

    ECU diagnosis information
    IPDM E/R Reference Value VALUES ON THE DIAGNOSIS TOOL TERMINAL LAYOUT PHYSICAL VALUES *1: MR16DDT engine models *2: Except MR16DDT engine models *3: CVT models *4: M/T models *5: With daytime running light system *6: Without daytime running light system *7: K9K engine mo ...

    Light & rain sensor
    Component Function Check 1.CHECK LIGHT & RAIN SENSOR 1. Clean light & rain sensor detection area of windshield fully. 2. Turn ignition switch ON. 3. Turn lighting switch AUTO. 4. With the light & rain sensor illuminating, check the auto light function. Is the inspection result no ...

    Intelligent key battery
    Removal and Installation 1. Release the lock knob at the back of the Intelligent Key and remove the mechanical key. 2. Insert a flat-blade screwdriver (A) wrapped with a cloth into the slit of the corner and twist it to separate the upper part from the lower part. CAUTION: • Do not touch t ...