Nissan Juke Service and Repair Manual : Engine knock

Description

CHART 16: ENGINE KNOCK

Diagnosis Procedure

1.CHECK ENGINE OIL

Check the grade of engine oil. Refer to LU-33, "Inspection".

Is the inspection result normal? YES >> GO TO 2.

NO >> Replace engine oil. Refer to LU-34, "Refilling".

2.CHECK ENGINE OIL LEVEL

Is the engine oil level correct? Yes or No Yes >> GO TO 3.

No >> Top up the oil.

3.CHECK ECM POWER SUPPLY AND GROUND CIRCUIT

Check ECM power supply and ground circuit. Refer to EC-885, "Diagnosis Procedure".

Is the inspection result normal? YES >> GO TO 4.

NO >> Repair or replace harness or connector.

4.CHECK WIRING HARNESS

Visually check the condition of the engine wiring harness.

Is the inspection result normal? YES >> GO TO 5.

NO >> Repair or replace harness or connector.

5.CHECK AIR INTAKE SYSTEM

Check air intake system. Refer to EM-280, "Removal and Installation".

Is the inspection result normal? YES >> GO TO 6.

NO >> Repair or replace air intake system.

6.CHECK ELECTRIC THROTTLE CONTROL ACTUATOR

Check electric throttle control actuator. Refer to EC-909, "Diagnosis Procedure".

Is the inspection result normal? YES >> GO TO 7.

NO >> Repair or replace.

7.CHECK MASS AIR FLOW SENSOR

Check mass air flow sensor. Refer to EC-902, "Component Inspection".

Is the inspection result normal? YES >> GO TO 8.

NO >> Repair or replace.

8.CHECK CATALYTIC CONVERTER

Is the catalytic converter clogged or deteriorated? Is the inspection result normal? YES >> GO TO 9.

NO >> Repair or replace.

9.CHECK HIGH PRESSURE SUPPLY PUMP (PRESSURE CONTROL VALVE)

Perform the TEST 3: HIGH PRESSURE SUPPLY PUMP (PRESSURE CONTROL VALVE). Refer to EC-868, "Work Procedure [TEST 3: High Pressure Supply Pump (Pressure Control Valve) Check]".

>> GO TO 10.

10.CHECK HIGH PRESSURE SUPPLY PUMP (VOLUMETRIC CONTROL VALVE)

Perform the TEST 4: HIGH PRESSURE SUPPLY PUMP (VOLUMETRIC CONTROL VALVE). Refer to EC- 869, "Work Procedure [TEST 4: High Pressure Supply Pump (Volumetric Control Valve) Check]".

>> GO TO 11.

11.CHECK RAIL HIGH PRESSURE CONTROL CIRCUIT

Perform the TEST 5: RAIL HIGH PRESSURE CONTROL CIRCUIT CHECK. Refer to EC-871, "Work Procedure (TEST 5: Rail High Pressure Regulation Check)".

>> GO TO 12.

12.CHECK MAJOR LEAK IN FUEL INJECTOR/FUEL INJECTORS OPEN

Perform the TEST 6: MAJOR LEAK IN FUEL INJECTOR/FUEL INJECTORS OPEN. Refer to EC-876, "Work Procedure (TEST 6: Fuel Injectors Leak Check)".

>> GO TO 13.

13.CHECK INCORRECT FUEL INJECTION QUANTITY

Perform the TEST 7: INCORRECT FUEL INJECTION QUANTITY. Refer to EC-877, "Work Procedure (TEST 7: Fuel Injection Quantity Check)".

>> INSPECTION END

    Excessive consumption
    Description CHART 15:EXCESSIVE CONSUMPTION Diagnosis Procedure 1.CHECK ECM POWER SUPPLY AND GROUND CIRCUIT Check ECM power supply and ground circuit. Refer to EC-885, "Diagnosis Procedure&q ...

    Engine overheating
    Description CHART 17: ENGINE OVERHEATING Diagnosis Procedure 1.CHECK COOLING SYSTEM Check the cooling system. Refer to CO-60, "Troubleshooting Chart". Is the inspection result normal? ...

    Other materials:

    Battery
    • Keep the battery surface clean and dry. Clean the battery with a solution of baking soda and water. • Make certain the terminal connections are clean and securely tightened. •  If the vehicle is not to be used for 30 days or longer, disconnect the negative battery terminal cable to preve ...

    Symptom diagnosis
    COMBINATION SWITCH SYSTEM SYMPTOMS Symptom Table 1. Perform “Data Monitor” of CONSULT-III to check for any malfunctioning item. 2. Check the malfunction combinations. 3. Identify the malfunctioning part from the agreed combination and repair or replace the part. ...

    Front wheel hub and knuckle
    Inspection COMPONENT PART Check that the mounting conditions (looseness, backlash) of each component and component conditions (wear, damage) are normal. WHEEL HUB ASSEMBLY (BEARING-INTEGRATED TYPE) Check the following items, and replace the part if necessary. • Move wheel hub assembly in ...