Nissan Juke Service and Repair Manual : Door sash tape

Exploded View

1. Front door panel


1. Front door panel
2. Front door sash tape 3. Rear door sash tape
4. Rear door panel

Front door sash tape: Do not reuse


Front door sash tape

FRONT DOOR SASH TAPE : Removal and Installation

REMOVAL

Heat door sash tape surface using a dryer, and then peel door sash tape.

CAUTION:
Never damage painted surface of door panel.

INSTALLATION

NOTE

:
For installation position of door sash tape, refer to the position as shown in the figure.

1. Front door panel


1. Front door panel
2. Front door sash tape 3. Rear door panel

R. Radius

D : 2.0 mm (0.08 in): Do not reuse


D : 2.0 mm (0.08 in)
E : 4.0 mm (0.16 in)

CAUTION:
• Degrease door panel mounting surface for sash tape.

• Paint grain or dust on mounting surface of sash tape may spoil exterior appearance if it remains.Clean the mounting surface and check that no paint grain or dust remains, before starting the operation.

• Never reuse blackout tape.

1. Affix door sash tape align blackout tape upper portion to rear door outer upper end.

2. Affix door sash tape (2) to door panel (3) by applying pressure using a squeegee (A) while peeling offrelease coated paper (1).

NOTE

:
• Peel release coated paper at distance of 10 – 20 mm (0.394 – 0.787 in) ahead (B) of squeegee and affixblackout paper.

• To prevent any bubbles from forming, slightly lift the portion, not yet affixed using squeegee, so that portion dose not contact with panel surface. Apply pressure and affix at a low and constant speed usingsqueegee tilted at 40 – 50° angle (pushing direction) (C) 30 – 45° angle (pulling direction) (D).

3. For small radius portion of hemming part, gradually apply pressure


3. For small radius portion of hemming part, gradually apply pressure and affix door sash tape (1) using squeegee (A) in 1 – 3 steps.

CAUTION:
Never wash the vehicle with in 24 hours so as to keep adhesive.

Rear door sash tape


Rear door sash tape

REAR DOOR SASH TAPE : Removal and Installation

REMOVAL

Heat door sash tape surface using a dryer, and then peel door sash tape.

CAUTION:
Never damage painted surface of door pane

l.

INSTALLATION

NOTE

:
For installation position of door sash tape, refer to the position as shown in the figure.

1. Rear door panel


1. Rear door panel
2. Rear door sash tape
3. Front door panel

R. Radius

D : 2.0 mm (0.08 in): Do not reuse


D : 2.0 mm (0.08 in)

CAUTION:
• Degrease door panel mounting surface for door sash tape.

• Paint grain or dust on mounting surface of door sash tape may spoil exterior appearance if it remains. Clean the mounting surface and check that no paint grain or dust remains, before starting the operation.

• Never reuse door sash tape.

1. Affix door sash tape align door sash tape upper portion to rear door outer upper end.

2. Affix door sash tape (2) to door panel (3) by applying pressure using a squeegee (A) while peeling off release coated paper (1).

NOTE

:
• Peel release coated paper at distance of 10 – 20 mm (0.394 – 0.787 in) ahead (B) of squeegee and affixblackout paper.

• To prevent any bubbles from forming, slightly lift the portion, not yet affixed using squeegee, so that portion dose not contact with panel surface. Apply pressure and affix at a low and constant speed using squeegee tilted at 40 – 50° angle (pushing direction) (C) 30 – 45° angle (pulling direction) (D).

3. For small radius portion of hemming part, gradually apply pressure


3. For small radius portion of hemming part, gradually apply pressure and affix door sash tape (1) using squeegee (A) in 1 – 3 steps.

CAUTION:
Never wash the vehicle with in 24 hours so as to keep adhesive.

Rear fender cover


    Door outside molding
    Exploded View 1. Front door panel 2. Front door outside molding 3. Rear door panel 4. Rear door outside molding 5. Door glass : Pawl Front door outside molding FRONT DOOR OUTSIDE MOLDING ...

    Rear fender cover
    Exploded View 1. Rear fender cover 2. Rear fender Removal and Installation REMOVAL Disengage rear fender cover fixing clips using remover tool (A), and then remove rear fender cover. CAUTI ...

    Other materials:

    P0132 A/F sensor 1
    DTC Logic DTC DETECTION LOGIC To judge the malfunction, the diagnosis checks that the A/F signal computed by ECM from the A/F sensor 1 signal is not inordinately high. DTC CONFIRMATION PROCEDURE 1.PRECONDITIONING If DTC Confirmation Procedure has been previously conducted, always turn ig ...

    P0746 pressure control solenoid A
    Description The line pressure solenoid valve regulates the oil pump discharge pressure to suit the driving condition in response to a signal sent from the TCM. DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE CAUTION: Always drive vehicle at a safe speed. NOTE: If “DTC CONFIRMAT ...

    A/C auto AMP. Connection recognition signal circuit
    Diagnosis Procedure 1.CHECK A/C AUTO AMP. CONNECTION RECOGNITION SIGNAL 1. Turn ignition switch ON. 2. Check voltage between combination meter harness connector and ground. Is the inspection result normal? YES >> INSPECTION END NO >> GO TO 2. 2.CHECK A/C AUTO AMP. CONNECTION R ...