Nissan Juke Service and Repair Manual : Door lock and unlock switch

Component Function Check

1.CHECK FUNCTION

1. Select “DOOR LOCK” of “BCM” using CONSULT-III.

2. Select “CDL LOCK SW”, “CDL UNLOCK SW” in “DATA MONITOR” mode.

3. Check that the function operates normally according to the following conditions.

Is the inspection result normal?


Is the inspection result normal? YES >> Door lock and unlock switch is OK.

NO >> Refer to DLK-254, "Diagnosis Procedure".

Diagnosis Procedure

1.CHECK DOOR LOCK AND UNLOCK SWITCH INPUT SIGNAL

1. Turn ignition switch OFF.

2. Disconnect power window main switch connector.

3. Check signal between power window main switch harness connector and ground using oscilloscope.

Is the inspection result normal?


Is the inspection result normal? YES >> GO TO 3.

NO >> GO TO 2.

2.CHECK DOOR LOCK AND UNLOCK SWITCH CIRCUIT

1. Disconnect BCM connector and front power window switch (passenger side) connector.

2. Check continuity between BCM harness connector and power window main switch harness connector.

3. Check continuity between BCM harness connector and ground.


3. Check continuity between BCM harness connector and ground.

Is the inspection result normal?


Is the inspection result normal? YES >> Replace BCM. Refer to BCS-93, "Removal and Installation".

NO >> Repair or replace harness.

3.CHECK DOOR LOCK AND UNLOCK SWITCH GROUND

Check continuity between power window main switch harness connector and ground.

Is the inspection result normal?


Is the inspection result normal? YES >> GO TO 4.

NO >> Repair or replace harness.

4.CHECK DOOR LOCK AND UNLOCK SWITCH

Refer to DLK-255, "Component Inspection".

Is the inspection result normal? YES >> GO TO 5.

NO >> Replace power window main switch. Refer to PWC-44, "Removal and Installation".

5.CHECK INTERMITTENT INCIDENT

Refer to GI-42, "Intermittent Incident".

>> INSPECTION END

Component Inspection

1.CHECK DOOR LOCK AND UNLOCK SWITCH

1. Turn ignition switch OFF.

2. Disconnect power window main switch connector.

3. Check continuity between power window main switch terminals.

Is the inspection result normal?


Is the inspection result normal? YES >> INSPECTION END

NO >> Replace power window main switch.

    Door lock actuator
    Driver side DRIVER SIDE : Component Function Check 1.CHECK FUNCTION 1. Select “DOOR LOCK” of “BCM” using CONSULT-III. 2. Select “DOOR LOCK” in “ACTIVE TEST” mode. 3. Check that the function opera ...

    Door request switch
    Component Function Check 1.CHECK FUNCTION 1. Select “INTELLIGENT KEY” of “BCM” using CONSULT-III. 2. Select “REQ SW-DR”, “REQ SW-AS” in “DATA MONITOR” mode. 3. Check that the function operates nor ...

    Other materials:

    If your vehicle overheats
    CAUTION • Do not continue to drive if your vehicle overheats. Doing so could cause engine damage or a vehicle fire. • To avoid the danger of being scalded, never remove the radiator cap while the engine is still hot. When the radiator cap is removed, pressurized hot water will spurt out, poss ...

    P0638 electric throttle control actuator function
    DTC Logic DTC DETECTION LOGIC NOTE: If DTC P0638 is displayed with DTC P0120 or P2100, first perform trouble diagnosis for DTC P0120 or P2100. Refer to EC-909, "DTC Logic" (P0120), EC-997, "DTC Logic" (P2100). Diagnosis Procedure 1.CHECK ELECTRIC THROTTLE CONTROL ACTU ...

    C1120, C1122, C1124, C1126 ABS in valve system
    DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.PRECONDITIONING If “DTC CONFIRMATION PROCEDURE” has been previously conducted, always turn ignition switch OFF and wait at least 10 seconds before conducting the next test. >> GO TO 2. 2.CHECK DTC DETECTION With CONSULT ...