Nissan Juke Service and Repair Manual : Differential side oil seal

Exploded View

2. Differential side oil seal (left side)1. Transaxle assembly
2. Differential side oil seal (left side) 3. Differential side oil seal (right side)

: Always replace after every: Vehicle front
disassembly.: Always replace after every
disassembly.

Removal and Installation: Genuine NISSAN CVT Fluid NS-2


Removal and Installation

REMOVAL

NOTE

:
Cap or plug openings to prevent fluid from spilling.

1. Remove the left and right front drive shafts. Refer to FAX-53, "Removal and Installation".

2. Use oil seal remover or a similar means and remove the differential side oil seal.

CAUTION:
When removing the differential side oil seal, be careful not to scratch the oil seal mounting surfaces of the transaxle case and converter housing.

INSTALLATION

Note the following, and install in the reverse order of removal.

CAUTION:
• Never reuse differential side oil seal.

• Apply Genuine NISSAN CVT Fluid NS-2 to the differential side oil seal lip and around the oil seal.

• When inserting the drive shaft, be sure to use a protector (SST: KV38107900). Refer to FAX-53, "Removal and Installation".

Use a drift (commercial service tool) and drive the differential side oil seal in until the amount of oil seal projection from the case edge matches dimensions (C) and (D).

CAUTION:
Be careful not to scratch the lip of the differential side oil seal when press-fitting it.

A : Differential side oil seal (left side) B : Differential side oil seal (right side)

Dimension “C” :Height difference from case end surface is within 1.8 ± 0.5 mm


Dimension “C” :Height difference from case end surface is within 1.8 ± 0.5 mm (0.071 ± 0.020 in).

Dimension “D” :Height difference from case end surface is within 1.8 ± 0.5 mm (0.071 ± 0.020 in).

NOTE

:
The reference is the pull-in direction of the differential side oil seal.

Inspection and Adjustment


Inspection and Adjustment

INSPECTION AFTER INSTALLATION

Check for CVT fluid leakage. Refer to TM-480, "Inspection".

ADJUSTMENT AFTER INSTALLATION

Adjust the CVT fluid level. Refer to TM-379, "Adjustment".

    Output speed sensor
    Exploded View 1. Transaxle assembly 2. Output speed sensor 3. O-ring : Vehicle front : Always replace after every disassembly. : N·m (kg-m, in-lb) : Genuine NISSAN CVT Fluid NS-2 Removal ...

    Water hose
    Exploded View 1. Hose clamp 2. Water hose A 3. Water hose B 4. Water hose B 5. Water bypass pipe 6. Hose clamp 7. Heater hose 8. Water hose C A. Water outlet B. Heater thermostat C ...

    Other materials:

    Security indicator lamp does not turn on or blink
    Description Security indicator lamp does not blink when ignition switch is in a position other than ON. NOTE: • Before performing the diagnosis, check “Work Flow”. Refer to SEC-47, "Work Flow". • Check that vehicle is under the condition shown in “CONDITIONS OF VEHICLE (OPERATI ...

    Front fender
    Exploded View 1. Front fender assembly 2. Front fender stiffener : Vehicle fr Removal and Installation REMOVAL 1. Remove front fillet molding. Refer to EXT-26, "FRONT FILLET MOLDING : Removal and Installation". 2. Remove front bumper fascia assembly. Refer to EXT-13, "Remo ...

    Precaution
    Precaution for Supplemental Restraint System (SRS) "AIR BAG" and "SEAT BELT PRE-TENSIONER" The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along with a front seat belt, helps to reduce the risk or severity of injury to the driver a ...