Nissan Juke Service and Repair Manual : Differential side oil seal

Exploded View

1. Transaxle assembly


1. Transaxle assembly 2. Differential side oil seal (left side) 3. Differential side oil seal (right side)

disassembly.: Always replace after every
disassembly.

Removal and Installation: Genuine NISSAN CVT Fluid NS-2


Removal and Installation

REMOVAL

NOTE

:
Cap or plug openings to prevent fluid from spilling.

1. Remove the left front drive shaft. Refer to FAX-22, "LEFT SIDE : Removal and Installation".

2. Remove the transfer assembly. Refer to DLN-93, "Removal and Installation".

3. Use oil seal remover or a similar means and remove the differential side oil seal.

CAUTION:
When removing the differential side oil seal, be careful not to scratch the oil seal mounting surfaces of the transaxle case and converter housing.

INSTALLATION

Note the following, and install in the reverse order of removal.

CAUTION:
• Never reuse differential side oil seal.

• Apply Genuine NISSAN CVT Fluid NS-2 to the differential side oil seal lip and around the oil seal.

• When inserting the drive shaft, be sure to use a protector (SST: KV38107900). Refer to FAX-22, "LEFT SIDE : Removal and Installation".

Use a drift (commercial service tool) and drive the differential side oil seal in until the amount of oil seal projection from the case edge matches dimensions (C) and (D).

CAUTION:
Be careful not to scratch the lip of the differential side oil seal when press-fitting it.

A : Differential side oil seal (left side) B : Differential side oil seal (right side)

Dimension “C” :Height difference from case end surface is within 1.8 ± 0.5 mm


Dimension “C” :Height difference from case end surface is within 1.8 ± 0.5 mm (0.071 ± 0.020 in).

Dimension “D” :Height difference from case end surface is within 1.0 ± 0.5 mm (0.039 ± 0.020 in).

NOTE

:
The reference is the pull-in direction of the differential side oil seal.

Inspection


Inspection

After completing installation, check for CVT fluid leakage and CVT fluid level. Refer to TM-184, "Inspection".

    Secondary speed sensor
    Exploded View 1. Transaxle assembly 2. Secondary speed sensor 3. O-ring : Always replace after every disassembly. : N·m (kg-m, in-lb) : Genuine NISSAN CVT Fluid NS-2 Removal and Installat ...

    Oil pump fitting bolt
    Description Replace the oil pump fitting bolt and the O-ring if oil leakage or exudes from the oil pump fitting bol Exploded View 1. Oil pump fitting bolt 2. O-ring 3. Transaxle assembly : ...

    Other materials:

    Diagnosis and repair work flow
    Work Flow OVERALL SEQUENCE DETAILED FLOW 1.INTERVIEW FOR MALFUNCTION Interview the symptom to the customer. >> GO TO 2. 2.SYMPTOM CHECK Check the symptom from the customer's information. >> GO TO 3. 3.BASIC INSPECTION Check the operation of each part. Check that any sym ...

    Inspection
    OIL LEAKAGE Make sure that gear oil is not leaking from transaxle or around it. OIL LEVEL 1. Remove filler plug (1) and gasket from transaxle case. 2. Check the oil level from filler plug mounting hole as shown in the figure. CAUTION: Never start engine while checking oil level. 3. Set a ...

    Rear shock absorber
    Exploded View 1. Suspension arm 2. Shock absorber 3. Bound bumper 4. Bound bumper cover 5. Washer 6. Bushing 7. Distance tube 8. Piston rod lock nut 9. Cap : Vehicle front : Always replace after every disassembly. : N·m (kg-m, ft-lb) Removal and Installation REMOVAL 1. Remove ...