Nissan Juke Service and Repair Manual : Diagnosis and repair work flow

Work Flow

OVERALL SEQUENCE

DETAILED FLOW


DETAILED FLOW

1.GET INFORMATION ABOUT SYMPTOM

Get detailed information from the customer about the symptom (the condition and the environment when the incident/malfunction occurs).

>> GO TO 2.

2.CHECK DTC

1. Check DTC of “ENGINE”, “BCM” and “IPDM E/R” using CONSULT-III.

2. Perform the following procedure if DTC is detected.

- Record DTC and freeze frame data (Print them out using CONSULT-III.) - Erase DTC.

- Study the relationship between the cause detected by DTC and the symptom described by the customer.

3. Check related service bulletins for information.

Are any symptoms described and any DTC detected? Symptom is described, DTC is detected>>GO TO 3.

Symptom is described, DTC is not detected>>GO TO 4.

Symptom is not described, DTC is detected>>GO TO 5.

3.CONFIRM THE SYMPTOM

Confirm the symptom described by the customer.

Connect CONSULT-III to the vehicle, and check self diagnostic results in real time.

Verify relation between the symptom and the condition when the symptom is detected.

>> GO TO 5.

4.CONFIRM THE SYMPTOM

Confirm the symptom described by the customer.

Connect CONSULT-III to the vehicle, and check self diagnostic results in real time.

Verify relation between the symptom and the condition when the symptom is detected.

>> GO TO 6.

5.PERFORM DTC CONFIRMATION PROCEDURE

Perform DTC Confirmation Procedure for the detected DTC, and then check that DTC is detected again.

At this time, always connect CONSULT-III to the vehicle, and check self diagnostic results in real time.

If two or more DTCs are detected, refer to BCS-66, "DTC Inspection Priority Chart" (BCM) or PCS-25, "DTC Index" (IPDM E/R), and determine trouble diagnosis order.

Is DTC detected? YES >> GO TO 7.

NO >> Refer to GI-42, "Intermittent Incident".

6.DETECT MALFUNCTIONING SYSTEM BY SYMPTOM DIAGNOSIS

Detect malfunctioning system according to SYMPTOM DIAGNOSIS based on the confirmed symptom in step 4, and determine the trouble diagnosis order based on possible causes and symptom.

>> GO TO 7.

7.DETECT MALFUNCTIONING PART BY DIAGNOSTIC PROCEDURE

Inspect according to Diagnostic Procedure of the system.

NOTE

:
The Diagnostic Procedure is described based on open and short circuit inspection.

Is malfunctioning part detected? YES >> GO TO 8.

NO >> Check voltage of related BCM terminals or IPDM E/R terminals using CONSULT-III.

8.REPAIR OR REPLACE THE MALFUNCTIONING PART

1. Repair or replace the malfunctioning part.

2. Reconnect parts or connectors disconnected during Diagnostic Procedure again after repair and replacement.

3. Check DTC. If DTC is detected, erase it.

>> GO TO 9.

9.FINAL CHECK

When DTC is detected in step 2, perform DTC CONFIRMATION PROCEDURE again, and then check that the malfunction is repaired securely.

When symptom is described by the customer, refer to confirmed symptom in step 3 or 4, and check that the symptom is not detected.

Does the symptom reappear? YES (DTC is detected)>>GO TO 7.

YES (Symptom remains)>>GO TO 6.

NO >> INSPECTION END

    Additional service when replacing control unit
    ECM ECM : Description Performing the following procedure can automatically activate recommunication of ECM and BCM, but only when the ECM is replaced with a new one*. *: New one means a virgin ...

    Other materials:

    B2195 anti-scanning
    DTC Logic DTC DETECTION LOGIC DTC CONFIRMATION PROCEDURE 1.PERFORM DTC CONFIRMATION PROCEDURE 1. Turn ignition switch ON. 2. Check DTC in “Self Diagnostic Result” mode of “BCM” using CONSULT-III. Is DTC detected? YES >> Refer to SEC-206, "Diagnosis Procedure". NO >&g ...

    Wheel Alignment
    HR16DE, K9K Measure value under unladen*2 conditions. *1: Since adjustment mechanism is not included, the value of the left and right wheels (both wheels) must be used as the standard value. *2: Fuel, engine coolant and lubricant are full. Spare tire, jack, hand tools and mats are in des ...

    Component parts
    Meter system METER SYSTEM : Component Parts Location 1. Fuel level sensor unit (main) 2. Front seat belt buckle switch (passenger side) 3. CVT shift selector assembly Refer to TM-131, "CVT CONTROL SYSTEM : Component Parts Location" (MR16DDT engine models). Refer to TM-314, &quo ...