Nissan Juke Service and Repair Manual : Daytime running light relay circuit

Component Function Check

1.CHECK DAYTIME RUNNING LIGHT OPERATION

1. Select “EXTERNAL LAMPS” of IPDM E/R active test item.CONSULT-III ACTIVE TEST


1. Select “EXTERNAL LAMPS” of IPDM E/R active test item.

2. With operating the test item, check that parking lamp, tail lamp and license plate lamp are turned ON.

TAIL : Parking lamp, tail lamp and license plate lamp ON Off : Parking lamp, tail lamp and license plate lamp OFF

Is the inspection result normal? YES >> Daytime running light relay circuit is normal.

NO >> Refer to EXL-50, "Diagnosis Procedure".

Diagnosis Procedure

1.CHECK DAYTIME RUNNING LIGHT RELAY FUSE

1. Turn ignition switch OFF.

2. Check that the following fuse is not fusing.

Gasoline engine models

Diesel engine models


Diesel engine models

Is the inspection result normal?


Is the inspection result normal? YES >> GO TO 2.

NO >> Replace the fuse after repairing the applicable circuit.

2.CHECK DAYTIME RUNNING LIGHT RELAY POWER SUPPLY

1. Remove daytime running light relay.

2. Check voltage between daytime running light relay harness connector and ground.

Is the inspection result normal?


Is the inspection result normal? YES >> GO TO 3.

NO >> Repair or replace harness.

3.CHECK DAYTIME RUNNING LIGHT RELAY

Check daytime running light relay. Refer to EXL-51, "Component Inspection".

Is the inspection result normal? YES >> GO TO 4.

NO >> Replace daytime running light relay.

4.CHECK DAYTIME RUNNING LIGHT RELAY CONTROL SIGNAL OUTPUT

1. Install daytime running light relay.CONSULT-III ACTIVE TEST


1. Install daytime running light relay.

2. Turn ignition switch ON.

3. Select “EXTERNAL LAMPS” of IPDM E/R active test item.

4. With operating the test item, check voltage between IPDM E/R harness connector and ground.

Is the inspection result normal?


Is the inspection result normal? YES >> Daytime running light relay circuit is OK.

Fixed at 0 V >>GO TO 5.

Fixed at battery voltage >>Replace IPDM E/R.

5.CHECK DAYTIME RUNNING LIGHT RELAY CONTROL SIGNAL OPEN CIRCUIT

1. Turn ignition switch OFF.

2. Remove daytime running light relay.

3. Disconnect IPDM E/R harness connector.

4. Check continuity between IPDM E/R harness connector and daytime running light relay harness connector.

Is the inspection result normal?


Is the inspection result normal? YES >> GO TO 6.

NO >> Repair or replace harness.

6.CHECK DAYTIME RUNNING LIGHT RELAY CONTROL SIGNAL SHORT CIRCUIT

Check continuity between IPDM E/R harness connector and ground.

Is the inspection result normal?


Is the inspection result normal? YES >> Replace IPDM E/R.

NO >> Repair or replace harness.

Component Inspection

1.CHECK DAYTIME RUNNING LIGHT RELAY

1. Turn ignition switch OFF.

2. Remove daytime running light relay.

3. Apply battery voltage to daytime running light relay between terminals 1 and 2.

4. Check continuity of daytime running light relay.

Is the inspection result normal?


Is the inspection result normal? YES >> Daytime running light relay is normal.

NO >> Replace daytime running light relay.

    Headlamp ground circuit
    Diagnosis Procedure 1.CHECK HEADLAMP GROUND OPEN CIRCUIT 1. Turn ignition switch OFF. 2. Disconnect headlamp connector. 3. Check continuity between headlamp harness connector and ground. Is the ...

    Headlamp aiming system (manual)
    Component Inspection 1.CHECK HEADLAMP AIMING SWITCH 1. Remove headlamp aiming switch. 2. Check resistance among each headlamp aiming switch terminal. Is the inspection result normal? YES >&g ...

    Other materials:

    Refilling
    1. IInstall reservoir tank if removed, and install radiator drain plug. CAUTION: Be sure to clean drain plug and install with new O-ring. Radiator drain plug : Refer to CO-17, "Exploded View". • If water drain plugs on cylinder block are removed, close and tighten them. Refer to EM ...

    B2608 starter relay
    DTC Logic DTC DETECTION LOGIC NOTE: • If DTC B2608 is displayed with DTC U1000, first perform the trouble diagnosis for DTC U1000. Refer to BCS-83, "DTC Logic". • If DTC B2608 is displayed with DTC U1010, first perform the trouble diagnosis for DTC U1010. Refer to BCS-84, "D ...

    Water hose
    Exploded View 1. Hose clamp 2. Water hose A. Water outlet B. Oil warm Removal and Installation REMOVAL WARNING: Never remove the radiator cap when the engine is hot. Serious burns could occur from high pressure coolant escaping from the radiator. CAUTION: Perform these steps after t ...