Nissan Juke Service and Repair Manual : Control cable

Exploded View

1. Control cable


1. Control cable
2. Lock plate
3. Transaxle assembly
4. Bracket A
5. Bracket B
6. CVT shift selector assembly

A: Manual lever
B: Grommet

: N·m (kg-m, in-lb): N·m (kg-m, ft-lb)
Removal and Installation: N·m (kg-m, in-lb)


Removal and Installation

INSTALLATION

CAUTION:
Always apply the parking brake before performing removal and installation.

1. Remove the battery. Refer to PG-124, "Removal and Installation".

2. Remove the control cable from the CVT shift selector assembly. Refer to TM-481, "Removal and Installation".

3. Disengage the pawls (B) of the grommet (A), and pull downwards to remove.

4. Remove the control cable installation nut from the manual lever.

5. Remove the lock plate (1).


5. Remove the lock plate (1).

6. Remove sub muffler from the mounting rubber and lower the sub muffler


6. Remove sub muffler from the mounting rubber and lower the sub muffler downward. Refer to EX-12, "Exploded View".

7. Lift up the heat plate.

8. Remove the control cable (1) from the bracket (2).

:Vehicle front


9. Remove the control cable from the vehicle.


9. Remove the control cable from the vehicle.

10. Remove bracket.

INSTALLATION

Note the following, and install in the reverse order of removal.

• From below the vehicle, press the grommet (A) into place until the pawls (B) make a click sound.

CAUTION:
• Place the grommet on the floor, then fasten it in place from below the vehicle.

• Check that pulling down on the grommet does not disconnect it.

• Pay attention to the following when connecting the control cable to the CVT


• Pay attention to the following when connecting the control cable to the CVT shift selector.

1. When connecting the control cable (1) to the CVT shift selector assembly (2), face the grooved surface of the rib (A) up and insert the control cable until it stops.

2. Install the socket (A) onto the CVT shift selector.


2. Install the socket (A) onto the CVT shift selector.

CAUTION:
• Place the socket onto the CVT shift lever, then fasten it in place from above.

• Check that the pulling on the socket does not disconnect it.

Inspection


Inspection

INSPECTION AFTER INSTALLATION

Check the CVT position. If a malfunction is found, adjust the CVT position. Refer to TM-383, "Inspection and Adjustment".

    CVT shift selector
    Exploded View 1. Selector lever knob 2. Lock pin 3. Knob cover 4 Position indication panel 5. CVT shift selector assembly 6. CVT shift selector harness assembly 7. Detent switch* 8. Shi ...

    Key interlock cable
    Exploded View 1. CVT shift selector assembly 2. Key interlock cable A: Key cylinder B: Clip C: Clip Removal and Installation REMOVAL CAUTION: Always apply the parking brake before perfor ...

    Other materials:

    Symptom diagnosis
    Squeak and rattle trouble diagnoses Work Flow CUSTOMER INTERVIEW Interview the customer if possible, to determine the conditions that exist when the noise occurs. Use the Diagnostic Worksheet during the interview to document the facts and conditions when the noise occurs and any of the cu ...

    Additional service when replacing control unit
    ECM ECM : Description Performing the following procedure can automatically activate recommunication of ECM and BCM, but only when the ECM is replaced with a new one*. *: New one means a virgin ECM that has never been energized on-board. (In this step, initialization procedure by CONSULT-I ...

    MR16DDT : Inspection and Adjustment
    INSPECTION Magnetic Switch Check • Before starting to check, disconnect the battery cable from the negative terminal. • Disconnect “M” terminal of starter motor. 1. Continuity test [between “S” terminal (A) and switch body] B : “B” terminal C : “M” terminal • Replace magnetic switch if co ...